×
  • all
  • Materials
  • Adhesives
  • Technology
  • Chemicals
  • Lifestyle

About Viechemie-SKICORP     |     Leadership     |     Group Websites     |     Contact Details

FINISHING CHEMICALS - Fashion for tomorrow

Achieve path-breaking leathers with
VIECHEMIE innovative & high-performing
leather finishes.

Leather Finishes

Viecryl IMP Micro

Solids content: 15%

pH value: 7-8

Composition: 7-8

Composition Viecryl Imp Micro is a very fine particle size, aqueous acrylic resin.

The main characteristics are:

  • retains a fine grain and break

  • excellent adhesion and grain tightening properties

  • helps the whole finish to penetrate better

  • Has a low Tg and excellent Light and Heat resistant

Viecryl Imp Micro Application:

  • Viecryl Imp Micro is an extremely fine particle size acrylic and just needs addition of a suitable penetrator like Vie Super Penetrator LC and Water for use as Full Grain and Corrected Grain Impregnation. It may also be used as a low cost adhesion binder and can also be added to base coats to improve adhesion and penetration.The product shows a clear improvement of the grain break and also equalizes the absorption of the leather surface without hardening the natural Leather temper.

  • Viecryl Imp Micro can also be used for full grain impregnation even for glazeable and polishable finishes on shoe upper leather. In this case, a proper penetration depth has to be checked very carefully.

  • The product is also suitable for grain tightening of corrected grain leather types either used alone or as an addition to other impregnation binders such as Viecryl Imp in order to increase the penetration depth of them.

  • Viecryl Imp Micro also improves the lasting behaviour in the shoe production, helping to set the shape and maintain it better.

  • The product is also used for absorption levelling pre-base coats or dark polishing finishes where products like the Vie Antik Waxes are used but only for the first coat or burnish/polish properties are reduced.

Viecryl IMP

Solids content: 35%

pH value: tba

Composition: Viecryl IMP is a fine particle size, aqueous acrylic resin.

The main characteristics are:

  • retains a fine grain and break

  • excellent adhesion and grain tightening properties

  • helps the whole finish to penetrate better

  • Has all round good properties

Viecryl IMP Application:

  • Viecryl IMP is preferably used alone or in combination with the softer/finer Viecryl Micro IMP for impregnation on corrected grain leathers. By using Viecryl IMP, excellent tightening of the grain can be acheived.

  • Viecryl IMP can also be used as a general purpose Acrylic for Base coats of all types of Leathers.

Viecryl IMP Micro

Solids content: tba

pH value: tba

Composition Viecryl Micro IMP is a very fine particle size, aqueous acrylic resin with a specifically designed penetrator.

The main characteristics are:

  • retains a fine grain and break

  • excellent adhesion and grain tightening properties

  • helps the whole finish to penetrate better

  • Has a low Tg and excellent Light and Heat resistant

Viecryl Micro IMP Application:

  • Viecryl Micro IMP contains an amount of a specially developed penetrating agent. For this reason, in most cases, no additional penetrator or solvent needs to be added when applying it alone. Application penetration is regulated by the addition of water. For very difficult surfaces (greasy leathers etc.) small additions of Vie Super penetrator can be added. The product shows a clear improvement of the grain break and also equalizes the absorption of the leather surface.

  • Viecryl Micro IMP can also be used for full grain impregnation even for glazeable and polishable finishes on shoe upper leather. In this case, a proper penetration depth has to be checked very carefully.

  • The product is also suitable for grain tightening of corrected grain leather types either used alone or as an addition to other impregnation binders such as Viecryl IMP in order to increase the penetration depth of them. The penetrator amount to be used should be calculated based only on the amount of the Viecryl IMP used in the impregnation mix as Viecryl Micro IMP already contains penetrator.

  • VViecryl Micro IMP also improves the lasting behaviour in the shoe production, helping to set the shape and maintain it better.

  • The product is also used for absorption levelling pre-base coats or dark polishing finishes where products like the Vie Antik Waxes are used but only for the first coat or burnish properties are reduced.

Viesol LT series

Composition Viesol LT dyes are dye solutions of metal complex dyes in a special combination of water-miscible, low toxicity solvents.

Description: The Viesol LT range can be used in Solvent, Aqueous or Water-miscible media and offers the following advantages:

The main characteristics are:

  • good light fastnessk

  • good fastness to migration

  • deep, even dyeings

  • high brilliance

  • high concentration

  • good water drop resistance

Viesol LT dyes have very good solubility. When Viesol LT dyes are to be used in a solvent media a pre-dilution with IPA is recommended to ensure compatibility or when used in Aqueous media it is also recommended to pre-dilute also with IPA although usually this is not necessary

Viecryl Imp Micro Application:

  • Spray or Dip dyeing of natural or drum-dyed crust for dyeing, shading and/or levelling, they can also be used for the following uses:

  • As brightening dyes in aqueous finishing preparations

  • In effect coats with polymer dispersions

  • In aqueous or organic effect coats with NC or CAB lacquers.

  • The compatibility with organic solvents has to be tested before. It depends on the composition of the lacquers and of the solvent mix. The addition of IPA improves the solubility.

  • Spray dyeing on suede and nubuck

Viesol AQ series - Viesol AQ dye range

Composition Viesol AQ dyes are concentrated solutions of metal complex dyes in a special combination of water-miscible, low toxicity solvents.

Description: The Viesol AQ range can be used in Solvent, Aqueous or Water-miscible media and offers the following advantages:

  • good light fastnessk

  • good fastness to migration

  • deep, even dyeings

  • high brilliance

  • high concentration

Viesol AQ dyes have very good solubility. When Viesol AQ dyes are to be used in a solvent media a pre-dilution with IPA is recommended to ensure compatibility or when used in Aqueous media it is also recommended to pre-dilute also with IPA although usually this is not necessary

Viesol AQ series Application:

  • Spray or Dip dyeing of natural or drum-dyed crust for dyeing, shading and/or levelling, they can also be used for the following uses:

  • As brightening dyes in aqueous finishing preparations

  • In effect coats with polymer dispersions

  • In aqueous or organic effect coats with NC or CAB lacquers.

  • The compatibility with organic solvents has to be tested before. It depends on the composition of the lacquers and of the solvent mix. The addition of IPA improves the solubility.

  • Spray dyeing on suede and nubuck

The Viesol AQ range comprises 17 primary colours:

  • Black RL

  • Black AS

  • Black W

  • Golden Yellow

  • Blue

  • Dark Brown

  • Lemon

  • Yellow 2R (Yellow Brown)

  • Royal Blue

  • Orange

  • Red

  • Brown

  • Fire Red

  • Rubine

  • Green

  • Magenta

Vie Microtint range

Application: Use 0 – 200 parts per kg in base coat as required, Sufficient Resin binders and even Casein binders are a must to ensure no migration and needs to be checked

Composition Vie Microtint range are highly dispersed Aqueous fine particle non-ionic, binder free pigments with excellent heat and light fastness.

The main characteristics are:

  • No over-loading of the grain and retains a fine break

  • Can be used for anionic or cationic finishes reducing inventory

  • Free of Heavy metals, formaldehyde and restricted substances

  • All colours have similar solids and volume for ease of use

  • All colours have excellent Light and Heat resistant

Typical Properties:

Colour Pigment type pH Solids %
VM Black (cover black) Carbon/Oxide Black 7 +- 40
VM Jet Black Carbon Black 7 +- 40
VM Deep Black Carbon Black 7 +- 40
VM Beige Iron Oxide 7 +- 40
VM Blue Organic 7 +- 40
VM Navy Blue Organic 7 +- 40
VM Fire Red Organic 7 +- 40
VM Brilliant Red Organic 7 +- 40
VM Violet Organic 7 +- 40
VM Red Violet Organic 7 +- 40
VM Lemon Organic 7 +- 40
VM Golden Yellow Organic 7 +- 40
VM Dark Brown Iron Oxide 7 +- 40
VM Tan Iron Oxide 7 +- 40
VM Green Organic 7 +- 40
VM Bright Green Organic 7 +- 40
VM Magenta Organic 7 +- 40
VM Rubine Organic 7 +- 40
VM Orange Organic 7 +- 40
VM White Titanium Dioxide 7 +- 40

Viepaque pigment range

Description Viepaque Pigments are available in a compact range of shades. Their fine dispersions make them ideal for use in the finishing of most leather types. They have been selected to obtain the maximum covering power possible. VP Pigments offer high physical properties. All VP Pigments are suitable for use in automated colour dispensers in conjunction with Computer colour match prediction systems.

Application: Their anionic nature makes them suitable for use with any anionic aqueous binders. It is important to use the correct primary colours when matching fashion shades in order to achieve a suitable fastness level for the finished product.For semi-aniline finishes, the required final shade is first matched with VP Pigments to get maximum coverage of defects, then lightened with an addition of 20% VP Tan or Beige(for tan and brown shades) or 20% white (for blue, red, green shades). Leather is then base coated with this lighter colour and finally matched to the required final shade with an over-spray of top coat with Viesol LD liquid dyes etc.

Composition Viepaque pigments are a range of aqueous anionic pigment dispersions designed specifically for leather finishing.They are finely ground and well dispersed in an acrylic medium and ground in such a way that pigment molecules are separated by micro spacers reducing flocculation and increasing tinctorial value and coverage.

The main characteristics are:

  • High coverage of defects, dramatic upgrading of low grade crust

  • Compact range of colours all with built in pigment spacers

  • Free of Heavy metals, formaldehyde and restricted substances

  • All colours have very good Light and Heat resistant

Typical Properties:

Colour Pigment type pH Solids %
VP Jet Black Organic/Inorganic 8.0 +- 12
VP Cover Black Organic/Inorganic 8.0 +- 45
VP Eco Black Organic/Inorganic 8.0 +- 45
VP Bright Black Organic/Inorganic 8.0 +- 45
VP Oxide Black Organic/Inorganic 8.0 +- 45
VP Blue Organic 8.0 +- 45
VP Magenta Organic 8.0 +- 45
VP Red Organic 8.0 +- 45
VP White Inorganic 8.0 +- 45
VP White B Inorganic 8.0 +- 45
VP Snow White Inorganic 8.0 +- 45
VP Lemon Inorganic 8.0 +- 45
VP Golden Yellow Inorganic 8.0 +- 45
VP Violet Inorganic 8.0 +- 45
VP Ochre Inorganic 8.0 +- 45
VP Orange Organic 8.0 +- 45
VP Tan Inorganic 8.0 +- 45
VP Bordeaux Organic 8.0 +- 45
VP Ultramarine Organic/Inorganic 8.0 +- 45
VP Brilliant Red Organic 8.0 +- 45
VP Green Organic 8.0 +- 45

Viesol LD dye range

Composition: Viesol LD dyes are highly concentrated solutions of metal complex dyes in a special combination of water-miscible, low toxicity solvents.

Description: The Viesol LD range can be used in Solvent, Aqueous or Water-miscible media and offers the following advantages:

  • good light fastness

  • good fastness to migration

  • deep, even dyeings

  • high brilliance

  • high concentration

Viesol LD dyes have very good solubility. When Viesol LD dyes are to be used in a solvent media a pre-dilution with IPA is recommended to ensure compatibility or when used in Aqueous media it is also recommended to pre-dilute also with IPA although usually this is not necessary

Viesol AQ series Application:

  • Spray or Dip dyeing of natural or drum-dyed crust for dyeing, shading and/or levelling, they can also be used for the following uses:

  • As brightening dyes in aqueous finishing preparations

  • In effect coats with polymer dispersions

  • In aqueous or organic effect coats with NC or CAB lacquers. The compatibility with organic solvents has to be tested before. It depends on the composition of the lacquers and of the solvent mix. The addition of IPA improves the solubility.

  • Spray dyeing on suede and nubuck

The Supronil HK range comprises 16 primary colours:

  • Black RE

  • Black RL

  • Black AS

  • Black W

  • Golden Yellow

  • Blue

  • Dark Brown

  • Lemon

  • Yellow 2R (Yellow Brown)

  • Royal Blue

  • Orange

  • Red

  • Brown

  • Fire Red

  • Rubine

  • Green

  • Magenta

Other Colours made with blends of these are also available on request

Vie Tint range

Application: Use 25 – 100 parts per kg in base coat as required, Organics maximum amount to be used is 50 parts per kg to avoid bronzing etc. Sufficient Resin binders and even Casein binders are a must to ensure no migration and needs to be checked.

Composition Vie Tint range are highly concentrated Aqueous fine particle non-ionic, binder free pigments with excellent heat and light fastness

The main characteristics are:

  • No over-loading of the grain and retains a fine break

  • Highly concentrated can be used for anionic or cationic finishes

  • Free of Heavy metals, formaldehyde and restricted substances

  • All colours have excellent Light and Heat resistant

Typical Properties:

Colour Pigment type pH Solids %
VT Black Carbon Black 8.8 +- 98
VT Jet Black Carbon Black 8.8 +- 22
VT Beige Iron Oxide 8.5 +- 58
VT Blue Organic 8.8 +- 44
VT Navy Blue Organic 8.8 +- 42
VT Fire Red Organic 8.8 +- 17
Vietint Ultrafine Green Organic 8.8 +- 42
VT Violet Organic 8.8 +- 16
VT Lemon Organic 8.8 +- 34
VT Golden Yellow Organic 8.8 +- 34
VT Dark Brown Iron Oxide 8.5 +- 50
VT Tan Iron Oxide 8.5 +- 58
VT Green Inorganic/Organic 8.8 +- 46
VT Magenta Organic 8.8 +- 40
VT Rubine Inorganic 8.8 +- 30
VT Orange Inorganic 8.8 +- 32
VT White Titanium Dioxide 8.5 +- 54
VT Lite White Titanium Dioxide 7.0 +- 50

Vietint Ultrafine range

Application: Use 50 – 100 parts per kg in base coat as required.

Composition Vietint Ultrafine range are aqueous fine particle sized anionic, casein bound transparent pigments, they are used to replace liquid dyes where high heat and light-fastness are required but with similar anilinity.

The main characteristics are:

  • No over-loading of the grain and retains a fine break

  • Transparent and finely divided particles acting like dyes\

  • Free of Heavy metals, formaldehyde and restricted substances

  • All colours have very good Light and Heat resistant much better than liquid dyes

Typical Properties:

Colour Pigment type pH Solids %
Vietint Ultrafine Jet Black Carbon Black 8.8 +- 15
Vietint Ultrafine Blue Organic 8.8 +- 18
Vietint Ultrafine Fire Red Organic 8.8 +- 18
Vietint Ultrafine Violet Organic 8.8 +- 13
Vietint Ultrafine Lemon Organic 8.8 +- 16
Vietint Ultrafine Golden Yellow Organic 8.8 +- 17
Vietint Ultrafine Green Organic 8.8 +- 19
Vietint Ultrafine Magenta Organic 8.8 +- 18
Vietint Ultrafine Orange Organic 8.8 +- 16
Vietint Ultrafine Bordeaux Organic 8.8 +-
Vietint Ultrafine Brilliant Green Organic 8.8 +-
Vietint Ultrafine Red Violet Organic 8.8 +-
Vietint Ultrafine White Inorganic/Organic 8.8 +-
Vietint Ultrafine Royal Blue Organic 8.8 +-
Vietint Ultrafine Dark Brown Inorganic 8.8 +-
Vietint Ultrafine Beige Inorganic 8.8 +-
Vietint Ultrafine Tan Inorganic 8.8 +-

Vievert CR6

Solids content: 10%

pH value: 4 – 6

Appearance: Clear to Slightly Yellow-Green

Description: Vievert CR6 is a colorless-slightly yellowish-greenish translucent liquid ready to use or diluted with water and applied onto the flesh side of the Leather. For maximum effect spray un-diluted

Composition Vievert CR6 is based on Vitriol and is useful for its antioxidant properties. Harmless Trivalent Chrome used for tanning has little or no toxicity, it can however under certain conditions oxidize and convert to the highly toxic Hexavalent Chrome which causes dermatitis and even cancer. Vievert CR6 when sprayed on the flesh side of Leather and absorbed into the Leather fibres will prevent this very effectively. Vievert CR6 has the ability to actually react with Hexavalent Chrome and convert it back to the non-toxic trivalent Chrome

Vievert CR6 Application:

Vievert CR6 is usually applied without dilution onto the flesh side of Leathers and allowed to absorb throughout the collagen fibres to efficiently prevent the formation of anti radicals which can easily convert harmless trivalent Chromium to highly toxic Hexavalent Chromium. It has the ability to convert toxic Hexavalent Chromium to non toxic Trivalent Chromium. It may also be diluted as required for application onto Leathers already treated in the wet process with other anti-oxidants like Vietan ZC6

The Viesol AQ range comprises 17 primary colours:

  • All types of Leathers to prevent formation of Hexavalent Chrome and convert Hexavalent Chrome to harmless Trivalent Chrome, used undiluted.
    Pray 1 x wet at around 2 – 3 grams per square foot on flesh side, dry well before packing etc

  • All types of Leathers previously treated in the wet process with suitable anti-oxidants like Vietan ZC6, use diluted with water 1:1 to 1:2.
    Spray 1 x wet at around 2 – 3 grams per square foot on flesh side, dry well before packing etc

N.B This product needs to be tested before use, on some Vegetable or Semi Vegetable Tanned Leathers it may change the colour, test a small area before use in production !!

Vieblock C6

Solids content: 10%

PH value: 7

Flash point: circa 62oC

Composition Vieblock C6 is based on Butylated Hydroxytoluene (BHT), and is a Lipophilic Organic compound, derived from Phenol and is useful for its antioxidant properties. Harmless Trivalent Chrome used for tanning has little or no toxicity, it can however under certain conditions oxidize and convert to the highly toxic Hexavalent Chrome which causes dermatitis and even cancer. Vieblock C6 when sprayed on the flesh side of Leather and absorbed into the Leather fibres will prevent this very effectively.

Description: Vieblock C6 is a colorless-slightly yellowish milky liquid ready to use or diluted with water and applied onto the flesh side of the Leather. For maximum effect spray un-diluted:

Vieblock C6 Application:

Vieblock C6 is usually applied without dilution onto the flesh side of Leathers and allowed to absorb throughout the collagen fibres to efficiently prevent the formation of anti radicals which can easily convert harmless trivalent Chromium to highly toxic Hexavalent Chromium. It may also be diluted as required for application onto Leathers already treated in the wet process with other anti-oxidants like Vietan ZC6. May also be used to replace Vietan ZC6 in the wet process, use 0.2 to 0.5% added with the fatliquors

The Viesol AQ range comprises 17 primary colours:

  • All types of Leathers to prevent formation of Hexavalent Chrome used undiluted
    spray 1 x wet at around 2 – 3 grams per square foot on flesh side

  • All types of Leathers previously treated in the wet process with suitable anti-oxidants like Vietan ZC6, use diluted with water 1:1 to 1:2
    Spray 1 x wet at around 2 – 3 grams per square foot on flesh side, dry well before packing etc

Vie Paste AS

Solids content: 27%

PH value: 3+-1

Composition Vie Paste AS is an Alkali swellable acrylic rheology modifier.

Description: Vie Paste AS is a whitish, low viscosity liquid. The product increases the viscosity and improves the levelling of aqueous base coats. Ensure the pH is above 8 for maximum thickening action, addition of a suitable alkali ensures full reaction.

Application: The thickening effect of Vie Paste AS depends not only on the amount used, but also on the kind of polymers in the formula. The thickening effect of Vie Paste AS is reduced by the presence of solvents. The required application amount should be tested in trials for each case and is normally between 10 – 50 parts per litre. In most cases, the viscosity for spraying application for aqueous finishes should ideally be between 12 – 25 secs Ford Cup 4 for spraying or 20 – 40 secs Ford Cup 4 for Roller coating

Vie Leveller

Solids content: 8%

PH value: 7+

Composition Vie Leveller is a yellowish liquid. The product improves the levelling of aqueous top coats and base coats. It helps to remove pinholes, craters, reticulation and improves general flow properties in spray or roller coat applications.

Application: Vie Leveller can be used in all aqueous finishing coats where a perfect flow out is needed. Vie Leveller can be used in aqueous roller coater applications and spray base coats or top coats. Vie Leveller also improves considerably the smoothness of finishes and increases gloss.

Example of application: Use in all aqueous mixes from 20 – 30 g/kg mix

Vie Paste RM

Solids content: 13%

PH value: 7+-

Composition Vie Paste RM is a non-ionic Associative Polyurethane rheology modifier polymers with surface-active substances.

Description: Vie Paste RM is a whitish, viscous liquid. The product increases the viscosity and improves the levelling of aqueous top coats and base coats. Unlike many thickeners has little or no effect on gloss and can even increase it.

Application: The thickening effect of Vie Paste RM depends not only on the amount used, but also on the kind of polymers in the formula. The thickening effect of Vie Paste RM is reduced by the presence of solvents. The required application amount should be tested in trials for each case and is normally between 15 – 50 parts per litre. In most cases, the viscosity for spraying application for aqueous finishes should ideally be between 12 – 25 secs Ford Cup 4 for spraying or 20 – 40 secs Ford Cup 4 for Roller coating

Viefix LTX

Solids content: tba

PH value: tba

Composition Viefix LTX is a aqueous low formaldehyde protein fixative to replace the traditionally used Formalin in Glazed, Imitation Glazed Leather finishes.

Description: Viefix LTX is clear water white to slightly milky white Protein crosslinking agent. The product forms no film and has a pleasant odour. It is intended as a safer and less toxic replacement for Formaldehyde for fixing Protein finishes.

Viefix LTX Application:

Viefix LTX is normally used as an over spray for fixing protein finishes. When used in combination with hard protein binders Viefix LTX gives good resistance to dry rubbing, and also some improvement to wet rubbing. The suggested method of use is to apply the protein base, middle and top coat, then, after drying apply a light fixing coat of Viefix LTX. Crosslinking occurs rapidly without the need for heat curing, normal drying process gives good results.

Examples of Application:

  • Goat, full grain, glazed finish

  • 700 p. Water

  • 50 p. Viepaque pigments

  • 50 p. Vie Lustre W

  • 100 p. Vie Lustre H

  • 100 p. Vie Lustre SS

  • spray 2 x

  • 700 p. Water

  • 50 p. Vie Lustre SS

  • 250 p. Vie Lustre H

  • spray 1 -2 x

  • 700 p. Water

  • 300 p. Viefix LTX

  • spray 1 – 2 x light , glaze, plate Hot

Viefix OC

Solids content: 15%

PH value: circa 4

Composition Viefix OC is a phosphonium based formaldehyde free Protein fixative in an aqueous medium

Description: Viefix OC is a colorless water soluble liquid crosslinking agent. The product forms no film and has little odour. Viefix OC is used as an over spray and can be used to fix both cationic and anionic protein finishes. It is intended as a safer replacement for the traditionally used formaldehyde and other aldehyde based fixatives

Viefix OC Application:

Viefix OC is normally used as an over spray for fixing protein finishes. When used in combination with hard protein binders Viefix OC gives good resistance to dry and even wet rubbing. The suggested method of use is to apply a season coat, then after drying spply a fixing coat with Viefix OC. Crosslinking occurs ralidly without the need for heat curing, normal drying is sufficient to fully react and optimize physicals.

Examples of Application:

Goat, full grain, glazed finish

  • 700 p. Water

  • 50 p. Viepaque pigments

  • 50 p. Vie Lustre W

  • 100 p. Vie Lustre H

  • 100 p. Vie Lustre SS

spray 2 x

  • 700 p. Water

  • 50 p. Vie Lustre SS

  • 250 p. Vie Lustre H

spray 1 -2 x

  • 700 p. Water

  • 300 p. Viefix OC

  • spray 1 – 2 x light , glaze, plate Hot

Vie Fresh range

Composition: Vie Fresh range are a specially designed range of Leather refreshers and mould eaters for all types of Leathers

Application: Use on all types of Leather usually on the flesh side by spraying but can also be used as a fungal cleaner on both sides by sponge or cloth application.

  • Eliminates unwanted odours from low grade fatliquors etc

  • Kills bacteria and fungus on old or badly stored Leathers

  • Refreshes dried out Leathers adding moisture without danger of fungal growth

  • Allows the Tanner to design special aromas for different articles

Vie Fresh articles:

  • A) Viefresh Neutral the flag-ship of the range, a fresh clean aroma even on old smelly leathers

  • B) Viefresh Fiore offers an aroma of Flowers in the Garden good for Upholstery and Fancy goods leathers

  • C) Viefresh Bello offers an aroma of beauty and is specially designed for Ladies fancy goods etc

  • D) Viefresh Cocco offers a wonderful natural coconut aroma and is good for Unisex leather articles

  • E) Viefresh Agrume offers a clean, crisp citrus smell and can be used for Unisex Leather articles

  • F) Viefresh Pine offers a clean, slightly sanitized Pine smell which leaves little or no odour after a few days ageing

  • G) Viefresh Liya offers a clean exciting aroma of mixed perfumes H) Viefresh Wild Leather offers a mixed perfume aroma which on many Leathers after ageing smells similar to Italian Vachetta

  • I) Viefresh Musk offers an aroma of Musk oil

  • J) Viefresh Lightfoot has little or no smell and has the highest amount of Nano technology biocide-fungicide and leaves the least Environmental Footprint with zero hazardous substances, not used on Fungus effected leather but used to prevent mould, fungus and Bacteria

Vie Feel 760

Solids content: 35% +-1%

PH value: 5+-1

Composition Vie Feel 760 is an Alkyl Siloxane Co-Polymeric Wax based feel agent for all types of Leathers

The main characteristics are:

  • Improves Abrasion resistance of Aqueous Top coats

  • Gives a Soft Slippery Waxy feel to the Finish

  • Has little effect on Gloss of Top coats

  • Can Improve Jetness of Black and Dark Leathers

Application: Use on all types of Leather in the Top coat to give a Soft Slippery Waxy non sticky feel and also to improve Jetness

Example of application: 1/ Add 1 – 8 % in aqueous Top Coats for all types of Leathers

Vie Feel 251

Solids content: 14-15%

PH value: 6-7

Composition Vie Feel 251 is a Silicone emulsion based feel agent for all types of Leathers

The main characteristics are:

  • Improves Abrasion resistance of Aqueous Top coats

  • Gives a Soft Slippery Waxy feel to the Finish

  • Has little effect on Gloss of Top coats

  • Can Improve Jetness of Black and Dark Leathers

Application: Use on all types of Leather in the Top coat to give a Soft Slippery Waxy non sticky feel and also to improve Jetness and Gloss

Example of application: Add 1 – 15 % in aqueous Top Coats for all types of Leathers

Vie Feel AR

Solids content: tba

PH value: tba

Composition Vie Feel AR is a silicone based feel agent for all types of Leathers

The main characteristics are:

  • Eliminates Tack in Top coats

  • Gives a Waxy, Silky, feel to the Finish

  • Has added perfume smell to reduce unpleasant Fish oil smells etc

  • Has little effect on Gloss at low dosages

Vie Feel AR Application Use on all types of Leather in the Top coat to reduce Tack and improve Feel and Smell

Example Applications:

  • 1/ Add 5 – 30 parts per kg in aqueous Top Coats for all types of Leathers

  • 2/ Use as an over-spray feel coat 10 – 50 parts Vie Feel AR in 1 Kg Water and spray light as required

  • 3/ Use with Vie Wax 203 as a Special waxy feel spray on Garment or Softee leathers

  • Vie Wax 203-100 parts

  • Vie Feel AR: 2-10 parts

  • Water: 200 -400 parts Water

  • Spray on Crust or Finished Leather as required

Vie Feel DP

Solids content: tba

PH value: tba

Composition Vie Feel DP is a Modified Poly Siloxane based feel agent for all types of Leathers

The main characteristics are:

  • Improves Abrasion resistance of Aqueous Top coats

  • Gives a Silky Slippery smooth feel to the Finish

  • Is Fatliquor compatible and helps to increase softness, sheen, tear strength etc

  • Economical cost vs performance

Vie Feel DP Application Use on all types of Leather in the Top coat to give a Slippery Silky smooth feel and also with Fatliquors for increasing softness, and also sheen and feel especially on Suedes, Nubucks and Velours

Example Applications:

  • Add 2 – 10 % in aqueous Top Coats for all types of Leathers

  • Add 1 – 4% in Fatliquors for increasing softness, sheen on suedes/nubucks etc

Vie Feel DW

Solids content: tba

PH value: tba

Composition Vie Feel DW is a Modified Poly Siloxane based feel agent for all types of Leathers

The main characteristics are:

  • Improves Abrasion resistance of Aqueous Top coats

  • Gives a Dry Waxy feel to the Finish

  • Has little effect and can even increase Gloss of Top coats

  • Can Improve Jetness of Black and Dark Leathers

Vie Feel DW Application Use on all types of Leather in the Top coat to give a Dry Waxy non sticky feel and also to improve Jetness

Example Applications:

  • 1/ Add 2 – 10 % in aqueous Top Coats for all types of Leathers

Vie Feel OL

Solids content: tba

PH value: tba

Composition Vie Feel OL is a Modified Poly Siloxane based feel agent for all types of Leathers

The main characteristics are:

  • Improves Abrasion resistance of Aqueous Top coats

  • Gives an Oily Slippery feel to the Finish

  • Has little effect on Gloss

  • Improves Plating and Embossing properties

Vie Feel DW Application Use on all types of Leather in the Top coat to give an oily feel and help plate release

Example Applications:

  • Add 1 – 10 % in aqueous Top Coats for all types of Leathers

Vie Feel RL

Solids content: 38%

PH value: 7

Composition Vie Feel RL is a non ionic dimethyl silicone fluid emulsion used as a plate release and feel agent for all types of Leathers.

The main characteristics are:

  • Improves Abrasion resistance of Aqueous Top coats

  • Gives a Silky slightly slippery feel to the Finish

  • Has little effect on Gloss, even increases gloss and clarity

  • Improves Plating and Embossing properties

Vie Feel RL Application Use on all types of Leather in the Top coat to give a Silky slippery feel and help plate release.

Example Applications:

  • Add 1 – 10 % in aqueous Top Coats for all types of Leathers

N.B: To ensure that the product quality is maintained, the container should be tightly sealed when not in use. Store at normal room temperature, and prevent prolonged exposure to extreme heat or freezing conditions, which may cause product separation. If separation does occur, thaw if frozen, stir the contents, and use in the normal manner.

Vie Feel S4

Solids content: tba

PH value: tba

Composition Vie Feel S4 is a Silicone emulsion based feel agent for all types of Leathers.

The main characteristics are:

  • Improves Abrasion resistance of Aqueous Top coats

  • GGives a Soft Slippery Waxy feel to the Finish

  • Actually improves Gloss of Top coats

  • Can Improve Jetness of Black and Dark Leathers

Vie Feel S4 Application Use on all types of Leather in the Top coat to give a Soft Slippery Waxy non sticky feel and also to improve Jetness and Gloss

Example Applications:

  • Add 1 – 15 % in aqueous Top Coats for all types of Leathers

Vie Feel SS

Solids content: tba

PH value: tba

Composition Vie Feel SS is an Alkyl Siloxane Co-Polymeric Wax based feel agent for all types of Leathers.

The main characteristics are:

  • Improves Abrasion resistance of Aqueous Top coats.

  • Gives a Soft Slippery Waxy feel to the Finish

  • Has little effect on Gloss of Top coats

  • Can Improve Jetness of Black and Dark Leathers

Vie Feel SS Application Use on all types of Leather in the Top coat to give a Soft Slippery Waxy non sticky feel and also to improve Jetness.

Example Applications:

  • Add 1 – 10 % in aqueous Top Coats for all types of Leathers.

Vie Feel SW

Solids content: tba

PH value: tba

Composition Vie Feel SW is a silicone based feel agent for all types of Leathers.

The main characteristics are:

  • Eliminates Tack in Top coats.

  • Gives a Sensual, Silky, Slippery feel to the Finish.

  • Dramatically increases Taber abrasion resistance, and eliminates scotch tape adhesion test failures.

  • Highly effective and can be used even at low dosage levels

Vie Feel SS Application: Use on all types of Leather in the Top coat to improve feel and taber abrasion etc

Example Applications:

  • Add 10 – 30 parts per kg in aqueous Top Coats for all types of Leathers

  • Use as an over-spray feel coat 10 – 50 parts Vie Feel SW in 1 Kg Water and spray light as required

  • Use with Vie Wax 203 as a Special waxy feel spray on Garment or Softee leathers Vie Wax 203 100 parts

  • Vie Feel SW 2 – 10 parts

  • Water 200 -500 parts Water

  • Spray on Crust or Finished Leather as required

Vie Feel WS

Solids content: tba

PH value: tba

Composition Vie Feel WS is a Modified Poly Siloxane based feel agent for all types of Leathers

The main characteristics are:

  • Improves Abrasion resistance of Aqueous Top coats

  • Gives a Silky Waxy feel to the Finish.

  • Has little effect and can even increase Gloss of Top coats.

  • Can Improve Jetness of Black and Dark Leathers.

  • Can be used directly on crust for polished naked leathers

  • Can be used with fatliquor for soft drapey nappas and garment leathers

Vie Feel WS Application: Use on all types of Leather in the Top coat to give a Silky Waxy non sticky feel and also to improve Jetness

Example Applications:

  • Add 2 – 10 % in aqueous Top Coats for all types of Leathers

  • Dilute 1 : 4 to 1 : 9 with water and sprayed onto crust, dry and polish felt, cloth or paper, mill to required softness and drape

  • Add 1 – 3 % with Fatliquors such as Vie Liquor SFF for super soft, special feeling naked leathers with increased yield

Vie Velour Silk DS

Solids content: 10%

PH value: tba

Composition Vie Velour Silk DS is a solvent based Modified Poly Siloxane feel agent for all types of Leathers

The main characteristics are:

  • Improves Abrasion resistance of Aqueous Top coats

  • Gives a Silky Waxy feel to the Finish.

  • Increases Gloss and Jetness of Colours, has good heat and light fastness.

  • Improves Plating and Embossing properties

Vie Velour Silk DS Application: Use on all types of Leather in the Solvent Top coats to give a Silky Waxy feel and help plate release

Example Applications:

  • Add 2 – 10 % in Solvent type Top Coats for all types of Leathers

  • Use 5 – 15% in Solvents such as IPA/MP etc as an overspray to improve feel, to stop sticky tapes from adhering, and for Nubuck, Suede and Velour sprays to improve colour and feel

Viepur-04

Solids content: 10%

PH value: tba

Composition Viepur-04 is an aqueous, aliphatic, tough PU resin.

  • Chemical Composition : – Aqueous Aliphatic PU dispersion

  • Physical Appearance : – Clear – Milky liquid

  • Total Solids : – 12.0 % +-1 %

  • pH : – 6.0 – 7.5

  • Viscosity(Ford cup B4) : – 10.0 – 15.0 Sec.

  • Film Properties : – Tough yet Elastic

The main characteristics are:

  • Retains a fine grain and break

  • Tough yet elastic.

  • Maintains the natural handle and touch of leather.

  • Improves adhesion

  • Suitable for base, intermediate or top coats

Vie Velour Silk DS Application:

  • Viepur-04 can be used in base coats, season coats or top coats for all type of Resin, Protein and PU finishes.

  • Due to its composition it is readily miscible in anionic and non-ionic product.

Example Applications:

  • 50-100 g / litre in anionic base coats.

  • 50 g / litre with protein binder in polishing finishes

  • 100-500 g/litre top coats

Viepur NI

Composition Viepur NI is an aqueous, aliphatic, fine particle PU resin.

TYPICAL PROPERTIES

  • Chemical Composition : – Aqueous Aliphatic PU dispersion

  • Physical Appearance : – Milky liquid

  • Total Solids : – 19.0 – 21.0 %

  • pH : 6.0 – 7.5

  • Viscosity(Ford cup B4) : – 10.0 – 15.0 Sec.

  • Film Properties : – Soft & Elastic

The main characteristics are:

  • retains a fine grain and break

  • Soft and elastic.

  • Maintains the natural handle and touch of leather

  • Improves adhesion

  • Compatible with Cationic and Anionic, use for base or intermediate coats

Vie Velour Silk DS Application:

  • Viepur NI can be used in base coat and season coat for all type of Resin, Protein and PU finishes.

  • Due to its composition it is readily miscible in anionic, cationic and non-ionic product. c. It can be used in Polishable ground coats.

Example Applications:

  • 50-100 g / litre in anionic and cationic finishes.

  • 50 g / litre with protein binder in polishing finishes

Viepur 903

Solids content: 25%+-1

PH value: 7-8

Composition Viepur 903 is an aqueous, Soft, Matt, modified anionic polyester PU especially designed for improving adhesion and all round physicals in base coats.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • has a Tg of -30oC

  • improves flow and all round physicals and is totally light and heat resistant

  • provides mattness to the finish without white break, increases coverage

Viepur 903 Application: Normally used with lower cost acrylics at any proportion to improve all round physicals

Example Applications:

  • Improve physicals especially Tg of all types of Leathers add 100 – 250 parts per kg

  • Natural Aniline Look Leathers with outstanding physicals

Water 300 – 400 parts
Vie Super Penetrator 50 parts
Viepur 902 200 parts
Viepur 903 150 parts
Vie Wax 203 50 parts
Vie Microtint Pigments 25 – 50 parts

Viepur 902

Solids content: 25%+-1

PH value: 7-8

Composition Viepur 902 is an aqueous, Soft, modified anionic polyester PU especially designed for improving adhesion and all round physicals in base coats.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • has a Tg of -30oC

  • improves flow and all round physicals and is totally light and heat resistant

Viepur 902 Application: Normally used with lower cost acrylics at any proportion to improve all round physicals.

Example Applications:

  • Improve physicals especially Tg of all types of Leathers add 100 – 250 parts per kg

  • Natural Aniline Look Leathers with outstanding physicals

Water 300 – 400 parts
Vie Super Penetrator 50 parts
Viepur 902 350 parts
Vie Filler SFT 50 parts
Vie Wax 203 50 parts
Vie Microtint Pigments 25 – 50 parts
Spray x 1 – 2, plate or iron 80oC, spray x 1 – 2 light, topcoat etc

Viepur Cat FP

Solids content: 10% solids +-

PH value: tba

Composition Viepur Cat FP is an aqueous, fine particle cationic polyester PU.

The main characteristics are:

  • retains a fine grain and break

  • excellent adhesion on all types of crust, even oily, greasy Leathers

  • excellent heat and light fastness

  • improves adhesion of weak or damaged grains, aids scotch tape test

Viepur Cat FP Application: Use as main binder for all types of Fashion Leathers in Cationic finishing systems, use wherever natural aspect is required.

Example Applications:

  • 1. Adhesion coat on Greasy/Oily crust

  • Spray, Pad or Roller coat x 1 wet

  • Finish as usual with anionic base and top coats

Water 450 parts
IPA/MP 50 parts
Viepur Cat FP 500 parts
  • 2. Sealer coats on all types of Leather

  • Spray x 1 wet

  • Iron or Plate 90oC low pressure

  • Finish as usual with anionic base and top coats

Water 475 parts
Viepur Cat FP 500 parts
Vie Microtint pigments 25 parts
  • 3. Naked look leathers

  • Spray x 1 – 2 light, Kiss plate or Iron 70oC, topcoat etc

Water 550 parts
Vie Super Penetrator LC 25 parts
Viepur Cat FP 50 parts
Viepur Cat Base 300 parts
Vie Microtint pigments 25 parts
  • 4. High cover natural nappa leathers

  • Spray x 1 – 2 light, Kiss plate or Iron 70oC, topcoat etc

Water 550 parts
Vie Super Penetrator LC 25 parts
Viepur Cat FP 50 parts
Viepur Cat Base 300 parts
Vie Microtint pigments 25 parts

Viepur Cat HP

Solids content: 10% solids +-

PH value: tba

Composition Viepur Cat HP is an aqueous, fine particle cationic polyester PU.

The main characteristics are:

  • retains a fine grain and break

  • excellent adhesion on all types of crust, even oily, greasy Leathers

  • excellent heat and light fastness

  • improves adhesion of weak or damaged grains, aids scotch tape test

Viepur Cat HP Application: Normally dilute 1: 1 with water and spray, can be coloured with Vietint pigments

Example Applications:

  • 1. Adhesion coat on Greasy/Oily crust

  • Spray, Pad or Roller coat x 1 wet

  • Finish as usual with anionic base and top coats

Water 450 parts
IPA/MP 50 parts
Viepur Cat FP 500 parts
  • 2. Sealer coats on all types of Leather

  • Spray x 1 wet

  • Iron or Plate 90oC low pressure

  • Finish as usual with anionic base and top coats

Water 475 parts
Viepur Cat HP 500 parts
Vie Microtint pigments 25 parts
  • 3. Naked look leathers

  • Spray x 1 – 2 light, Kiss plate or Iron 70oC, topcoat etc

Water 575 parts
Vie Super Penetrator LC 50 parts
Viepur Cat HP 300 parts
Viepur Cat Base 50 parts
Vie Microtint pigments 25 parts

Viepur Catbase

Solids content: 13% +-0.5

PH value: 3.4-3.8

Composition: Viepur Catbase is an aqueous, fine particle cationic polyester PU with wax, oils and other auxiliaries, ready to use.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • seals off damaged grain, upgrades

  • improves elasticity of the grain layer

Viepur Catbase Application: Normally dilute 1: 1 with water and spray, can be coloured with Vie Tint pigments

Example Applications:

  • Iron or Plate 90oC low pressure

  • Finish as usual with anionic base and top coats

Water 475 parts
Viepur Catbase 500 parts
Vie Tint pigments 25 parts
Spray x 1 wet

Viepur Compact 96

Solids content: 27% solids

PH value: circa 8

Composition Viepur Compact 96 is an aqueous, modified PU/Acrylate Compact binder ready to use alone or with other Viecryl or Viepur products etc as required.

The main characteristics are:

  • retains a fine grain and break, yet has high covering power

  • maintains the softness of the leather, excellent embossing properties

  • gives high adhesion even on oily and greasy crust

  • low tack, good heat and light fastness

Viepur Compact 96 Application: Normally just add pigment and apply by roller coat, add water to reduce viscosity for spray application

Example Applications:

  • 1. Classic Smooth Corrected grain Bovine Box Leather

Viepur Compact 96 800 parts
Vietint Pigment mix 200 parts
Roller coat x 2 – 3

Finish as usual with anionic base and top coats

  • 2. Natural Look Full Grain Bovine Leathers

Water 200 parts
Viecryl 7 100 parts
Viepur Compact 96 600 parts
Vie Tint Pigments 50 – 100 parts
Spray x 1 – 2, plate or iron 80oC, spray x 1 – 2 light, topcoat etc

Viepur Compact X’treme

Solids content: 25%

PH value: circa 7

Composition Viepur Compact X’treme is an aqueous, soft and stretchy, high covering yet with very low tack Compact Binder based on a combination of state of the art core-shell acrylics and micro aliphatic polyurethanes with all necessary fillers, waxes, and other auxiliaries and is ready to use. Every winter thousands of Leather Garments and other articles get damaged beyond repair by exposure to extreme temperatures as low as -30oC and the whole articles cracks like glass and cannot be repaired, Viepur Compact X’treme can withstand over minus 30oC without damage….

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather even on super soft crust

  • gives excellent coverage, yet maintains an extremely natural look

  • Has good Light and Heat resistant and cold resistant (Tg) to over minus 30oC

Viepur Compact X’treme Application: Use on all types of Leather, particularily soft nappa, furniture, sports shoe etc.

Example Applications:

  • 1. Export Garment Leather high performance

Water 100 – 500 parts
Viepur Compact X’treme 250 – 500 parts
Vie Microtint pigments 25 – 125 parts
Spray x 1 – 2, kiss plate or iron 70 – 90oC, spray x 1 – 2 light to cover, spray top coat etc
  • 2. Natural Look Garment Sheep

Water 300 – 500 parts
Viecryl-7 or Viecryl Microbinder 150 parts
Viepur Compact X’treme 350 parts
Vie Microtint pigments 50 – 100 parts
Spray x 1 – 2, kiss plate or iron 70-90oC, spray x 1 – 2 light to cover, spray top coat etc
  • 3. Natural Look Garment Sheep on very low grade

  • First Pad x 1 coat wet of Polishable Stucco:

Water 250 – 500 parts
Vie Revive CT 500 parts
Vie Microtint pigments 25 – 50 parts
Dry well, polish on felt, linen cloth or reversed buffing paper, then pad or spray x 1 – 2 base
Water 250 – 350 parts
Viecryl 7 100 -150 parts
Viepur Compact X’treme 400 – 500 parts
Vietint pigments 25 – 75 parts
Vie Lustre SS 25 – 50 parts
Spray x 1 – 2, plate, iron or Emboss 70 – 90 oC, spray x 1 – 2 light to cover, spray top coat etc

Viepur Flow

Solids content: tba

PH value: tba

Composition Viepur Flow is an aqueous, Soft, modified anionic polyester PU with coalescents especially designed for improving adhesion and all round physicals in base coats.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • has a Tg of -40oC

  • improves flow and all round physicals and is totally light and heat resistant

Viepur flow Application: Normally used with lower cost acrylics at any proportion to improve all round physicals.

Example Applications:

  • 1. Improve physicals expecially Tg of all types of Leathers add 100 – 250 parts per kg

  • 2. Natural Aniline Look Leathers with outstanding physicals.

Water 300 – 400 parts
Vie Super Penetrator 50 parts
Viepur flow 350 parts
Vie Filler SFT 50 parts
Vie Wax 203 50 parts
Vie Tint Pigments 25 – 50 parts

Spray x 1 – 2, plate or iron 80oC, spray x 1 – 2 light, topcoat etc

Viepur Micro

Solids content: tba

PH value: tba

Composition Viepur Micro is an aqueous, fine particle anionic polyester PU with coalescents and other auxiliaries, ready to use, especially designed for adhesion coats.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather even on super soft crust

  • gives high adhesion even on oily and greasy crust

  • unlike most adhesion Pu resins it is totally light and heat resistant

Viepur Micro Application: Normally dilute with water and either IPA/MP or Vie Super Penetrator and spray.

Example Applications:

  • 1. Adhesion on Oily/Greasy crust

Water 450 parts
IPA/MP 100 parts
Vie Super Penetrator 50 parts
Viepur Micro 400 parts
Spray x 1 wet

Finish as usual with anionic base and top coats

  • 2. Natural Aniline Look Leathers

Water 450 parts
Viepur Micro 500 parts
Vie Filler SFT 50 parts
Vie Wax 203 50 parts
Vie Tint Ultrafine Pigments 25 – 50 parts

Spray x 1 – 2, plate or iron 80oC, spray x 1 – 2 light, topcoat etc

Viepur Velour Fix

Solids content: circa 8 %

PH value: tba

Composition: Viepur Velour Fix is an aqueous, fine particle anionic polyester PU with coalescents and other auxiliaries, ready to use, especially designed for fixing loose dust and dyes on nubucks, suedes and velours.

Description: Viepur Velour Fix is a slightly milky liquid of low viscosity. The product produces a very thin, medium soft, elastic, non-sticky film of relatively low thermoplasticity and with good swelling resistance in water. As it contains no emulsifiers it has little or no effect on dynamic or static water resistance on performance Leathers.

Viepur Velour Fix Application: Viepur Velour Fix is a special binder for thin, almost invisible fixation of dyes and dust for suedes, nubucks, velours or naked drum dyed Leather. Due to the low thermoplasticity, it can also perfectly be used where hot stamping may be carried out by the article maker (bags, belts etc).

Example Applications:

  • 1. Colour fixation on standard suedes and nubucks:

Water 500 parts
Viepur Velour Fix 500 parts

Spray x 1 – 2 as required, dry well between coats, and give final brush with soft brush or sponge to recover nap

  • 2. Levelling/Upgrading Nubuck/Suede Leathers

Water 800 – 500 parts
Viepur Velour Fix 300 – 500 parts
Vie Wax 250 0 – 25 parts
Vie Tint Microfine Pigments 5 – 25 parts
Viesol LD dyes 5 – 25 parts
Viefeel RL or SS 0 – 25 parts

Spray x 1 – 2, Brush, spray x 1 – 2 light, Brush, Stake, Mill etc

  • 3. Colour fixation on Water-Proof Suedes, Nubucks and Drum Dyed crust:

Viepur Velour Fix 1000 parts
Vie Feel RL or SS 0 – 2 parts

Viepur-01

Solids content: circa 20%

PH value: tba

Composition: Viepur-01 is an aqueous, medium soft anionic polyester PU with special additives to be used in base coats of all types of Leathers to boost all round physical properties.

Description: Viepur-01 is a colourless-whitish, dispersion of low to medium viscosity. The product produces a clear, medium soft, tough-elastic film of low tackiness.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • shows good coverage and fill

  • improves all round physicals and is totally Light and Heat resistant

Viepur-01 Application: Normally used with lower cost acrylics at any proportion to improve all round physicals.

Example Applications:

  • 1. Improve physicals of all types of Leathers add 100 – 250 parts per kg

  • 2. Natural Aniline Look Leathers with good physicals

Water 225 parts
Vie Super Penetrator 50 parts
Viecryl Micro Binder 100 parts
Vie Micro Compact 250 parts
Viepur-01 150 parts
Vie Filler SFT 75 parts
Vie Wax 203 50 parts
Vie Lustre H 50 parts
Vietint Ultrafine pigments 50 parts

Spray x 1 – 2 , plate or iron 80oC, spray x 1 – 2 light, topcoat etc

Viepur-04

Solids content: Circa 13% solids

PH value: tba

Composition: Viepur-04 is an aqueous, fine particle anionic polyester PU with coalescents and other auxiliaries, ready to use, especially designed for adhesion coats.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • gives high adhesion even on oily and greasy crust

  • unlike most adhesion Pu resins it is totally light and heat resistant

Viepur-04 Application: Normally dilute with water and either IPA/MP or Vie Super Penetrator and spray.

Example Applications:

  • 1. Adhesion on Oily/Greasy crust

Water 450 parts
IPA/MP 100 parts
Vie Super Penetrator 50 parts
Viepur-04 400 parts
Spray x 1 wet

Finish as usual with anionic base and top coats

  • 2. Natural Aniline Look Leathers

Water 475 parts
Viepur-04 400 parts
Vie Filler SFT 25 parts
Vie Wax 203 50 parts
Vie Lustre SS 25 parts
Vie Tint Pigments 10 – 25 parts

Spray x 1 – 2, plate or iron 80oC, spray x 1 – 2 light, topcoat etc

Viepur-07

Solids content: circa 7 %

PH value: tba

Composition: Viepur-07 is an aqueous, fine particle anionic polyester PU with coalescents and other auxiliaries, ready to use, especially designed for adhesion coats.

Description: Viepur-07 is a slightly milky liquid of low viscosity. The product produces a very thin, medium soft, elastic, non-sticky film of relatively low thermoplasticity and with good swelling resistance in water.

Viepur-07 Application: Viepur-07 is a special binder for thin, natural finishes with good physical properties. Due to the low thermoplasticity, it can also perfectly be used in combinations for polishable base coats.

Example Applications:

  • 1. Adhesion on Oily/Greasy crust

Water 450 parts
IPA/MP 100 parts
Vie Super Penetrator LC 100 parts
Viepur-07 400 parts
Spray x 1 wet

Finish as usual with anionic base and top coats

  • 2. Levelling Nubuck/Suede Leathers

Water 800 – 500 parts
Viepur-07 300 – 500 parts
Vie Wax 250 0 – 25 parts
Vie Lustre SS 50 parts
Vie Tint Ultrafine Pigments 5 – 25 parts
Viefeel SW(N) 0 – 10 parts

Spray x 1 – 2, plate or iron 80oC, spray x 1 – 2 light, topcoat etc

Viepur-35

Solids content: 20%

PH value: tba

Composition: Viepur-35 is an aqueous, fine particle anionic polyester PU with coalescents and other auxiliaries, ready to use, especially designed for adhesion coats.Viepur-35 is a transparent dispersion of a low viscosity Aliphatic. The product forms a clear, soft very elastic film of low tackiness and good swelling resistance in water.

Viepur-35 has the following outstanding properties:

  • high adhesion values
  • excellent polishing and glazing behaviour, used together with suitable additives
  • increases elasticity and wet rubs of conventional polishing and glazed base coats
  • no grain overloading
  • good solvent resistance
  • improves the penetration of the finishes

Viepur-35 Application: Normally dilute with water and either IPA/MP or Vie Super Penetrator and spray

Example Applications:

  • 1. Adhesion on Oily/Greasy crust

Water 450 parts
IPA/MP 100 parts
Vie Super Penetrator LC 100 parts
Viepur-35 400 parts
Spray x 1 wet

Finish as usual with anionic base and top coats

  • 2. Natural Aniline Look Leathers

Water 450 parts
Viepur-35 500 parts
Vie Filler SFT (LC) 50 parts
Vie Lustre SS 50 parts
Vie Wax 250 50 parts
Vie Tint Ultrafine Pigments 25 – 50 parts

Spray x 1 – 2, plate or iron 80oC, spray x 1 – 2 light, topcoat etc

Viepur-89

Solids content: Circa 15%

PH value: 7 +-1

Composition: Viepur-89 is an aqueous, fine particle modified Aromatic PU dispersion, ready to use, especially designed for adhesion coats. Viepur-89 forms a very soft, elastic and sticky film and has been modified to penetrate deeply, most competitors’ products tend not to penetrate and although improve adhesion of Leather finish to the epidermis, there is often a weakness between the Epidermal and Dermal layers and adhesion tests often fail with removal of finish with the weakened grain.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • gives high adhesion even on oily and greasy crust

  • advantage over most aromatic Pu resins as it penetrates deeply into the epidermal/dermal junction

Viepur-89 Application: Normally dilute with water and either IPA/MP or Vie Super Penetrator and spray.

Example Applications:

  • 1. Adhesion on Oily/Greasy crust

Water 450 parts
IPA/MP 100 parts
Vie Super Penetrator 50 parts
Viepur-89 400 parts
Spray x 1 wet

Finish as usual with anionic base and top coats

  • 2. Natural Aniline Look Leathers

Water 450 parts
Viepur-89 500 parts
Vie Filler SFT 50 parts
Vie Wax 203 50 parts
Vie Microtint Pigments 25 – 50 parts

Spray x 1 – 2, plate or iron 80oC, spray x 1 – 2 light, topcoat etc

Viecryl VA

Solids content: 40%

PH value: 4.8 – 5.8

Composition Viecryl VA is an aqueous, soft, elastic copolymer emulsion of vinyl acetate and ethylene with relatively low tack yet with a strong adhesive power, having an opaque film it covers defects well and gives a good foundation to further finishing. Particularly suited to lightly of heavily buffed leathers as the first ground coat

The main characteristics are:

  • gives excellent adhesion without use of high cost PU resins

  • Retains a fine grain and break

  • maintains the softness of the leather

  • gives good sealing and covering without overloading the grain

  • medium-high tack and excellent Light and Heat resistant

Viecryl VA Application:

  • Use on all types of Leather as first ground, sealer or adhesion coat, used for general purpose and all round physical properties

Example Applications:

  • All types of Corrected Grain Leathers:

  • Dilute 1: 1 and spray medium-wet, dry well and plate or iron, continue with standard finish. If penetrator is needed, dilute penetrator with water before addition of Viecryl VA

Viecryl FA

Solids content: 40%

PH value: 5-6

Composition Viecryl FA is an unplasticized, Copolymer resin of Ethylene Vinyl Acetate.

The main characteristics are:

  • Forms a soft tacky film

  • excellent adhesion and flexibility

  • designed as an adhesive for all most kinds of foils and laminates

  • very natural look and handle

Viecryl FA Application: Viecryl FA is designed solely as an adhesive for Foils and laminates onto many substrates, in particular Leather. Dilute 2:1 for Roller or Blade application or up to 1:2 with water for spray application. For especially absorbent surfaces it may be necessary to spray x 2 times, dry check tackiness across the substrate, apply foil or laminate and hot plate 90oC to 120oC for 3-5 seconds dwell. Check adhesion as many foils have a different character and some need higher temperature to activate internal adhesives

Viecryl 777

Solids content: 16%

PH value: 8+-1

Composition Viecryl 777 is an aqueous, soft and elastic fine particle acrylic with outstanding penetration even on difficult crust.

The main characteristics are:

  • Retains a fine grain and break

  • Maintains the softness of the leather

  • Helps the whole finish to penetrate better

  • Has a low Tg and excellent Light and Heat resistant

Viecryl 777 Application: Use on all types of Leather with other Acrylics, Pu resins and auxiliaries to aid penetration and adhesion. Used alone with pigments and auxiliaries for Aniline looks

Example Applications: Natural Look Garment or Softy Leathers for export market

Water 375 parts
Vie Super Penetrator LC 25 parts
Viepur Micro 50 parts
Vie Filler SFT 50 parts
Vie Wax 5050 50 parts
Viecryl 777 100 parts
Viecryl Micro Compact 200 parts
Vie Microtint Pigments 50 parts

Spray x 1 – 2 ,plate or iron 80oC, spray x 1 – 2 light top coat etc

Viecryl 93

Solids content: 32%

PH value: 5.5+-0.5

Composition Viecryl 93 is an aqueous, soft, micro particle highly elastic acrylic with good penetrating properties and good all round properties.

The main characteristics are:

  • Exhibits a clear, transparent and highly flexible film

  • Excellent penetration properties

  • Retains a fine grain and break

  • Maintains the softness of the leather and a natural look

  • Offers excellent adhesion properties

  • Good all round physicals

  • May also be used as an Impregnation binder

Viecryl 93 Application: Viecryl 93 is a fine particle extremely soft elastic Acrylic binder with excellent penetration properties. It can be used in Impregnation coats, Ground coats, or Base coats alone or with other suitable binders etc. Use on all types of Leather with other Acrylics, PUs and auxiliaries for general purpose and all round physical properties

Example Applications:

Natural Aniline Softee Leathers for export market

Water 300 parts
Vie Super Penetrator LC 25 parts
Viecryl 7 100 parts
Vie Filler SFT 50 parts
Vie Wax 250 50 parts
Vie Lustre XG 75 parts
Viepur-01 or 902 50 parts
Viecryl 93 300 parts
Vie Tint Pigments 50 parts

Spray x 1 – 2 , plate or iron 80oC, spray x 1 – 2 light top coat etc

Corrected Grain Soft tight impregnation

Water 450-500 parts
Vie Super Penetrator LG 150-200 parts
Viecryl 93 350 parts

Viecryl 71

Solids content: 25%

PH value: 7-8

Composition Viecryl 71 is an aqueous, soft, elastic acrylic with relatively low tack and good cold resistance

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leathe

  • Offers excellent embossing and plating properties

  • low tack and excellent Light and Heat resistant

Viecryl 71 Application: Use on all types of Leather with other Acrylics, Pus and auxiliaries for general purpose and all round physical properties

Example Applications:

Natural Aniline Softee Leathers for export market

Water 300 parts
Vie Super Penetrator LC 25 parts
Viecryl 777 100 parts
Vie Filler SFT(LC) 50 parts
Vie Wax 5050 50 parts
Vie Lustre SS 75 parts
Viepur-01 or 902 50 parts
Viecryl 39 50 parts
Viecryl 71 300 parts
Vie Microtint Pigments 50 parts

Spray x 1 – 2 , plate or iron 80oC, spray x 1 – 2 light top coat etc

Viecryl 57

Solids content: 20%

PH value: 8+-1

Composition Viecryl 57 is an aqueous, soft and elastic fine particle acrylic with outstanding penetration even on difficult crust.

The main characteristics are:

  • Retains a fine grain and break

  • Maintains the softness of the leather and a natural look

  • helps the whole finish to penetrate better

  • Has a low Tg and excellent Light and Heat resistant

Viecryl 93 Application: Use on all types of Leather with other Acrylics, Pu resins and auxiliaries to aid penetration and adhesion. Used alone with pigments and auxiliaries for Aniline or Naked looks

Example Applications:

Natural Look Garment or Softy Leathers for export market

Water 375 parts
Vie Super Penetrator LC 25 parts
Viecryl 57 100 parts
Viepur 35 50 parts
Vie Filler SFT (LC) 50 parts
Vie Wax 505 50 parts
Viecryl 55 200 parts
Vie Microtint Pigments 50 parts

Spray x 1 – 2 ,plate or iron 80oC, spray x 1 – 2 light top coat etc

Viecryl 55

Solids content: 26%

PH value: 7-8

Composition Viecryl 55 is an aqueous, soft, elastic acrylic with relatively low tack and good cold resistance

The main characteristics are:

  • retains a fine grain and break

  • Excellent penetration properties

  • gives good filling and covering without overloading the grain

  • medium tack and excellent Light and Heat resistant

Viecryl 55 Application: Use on all types of Leather with other Acrylics, Pus and auxiliaries for general purpose and all round physical properties

Example Applications:

Natural Aniline Softee Leathers for export market

Water 300 parts
Vie Super Penetrator LC 25 parts
Viecryl 7 100 parts
Vie Filler SFT(LC) 50 parts
Vie Wax 505 50 parts
Vie Lustre XG 75 parts
Vie Lustre SS 75 parts
Viepur-01 50 parts
Viecryl 55 300 parts
Vie Microtint Pigments 50 parts

Vie Compound V

Solids content: 26% +-1%

PH value: 8+-1

Composition Vie Compound V is a highly viscous special compound composed of high filling encapsulated microspheres, soft extendable acrylic copolymers, a synergistic blend of fillers dispersion containing and other high filling substances. It is designed to supplement any stucco operation by completing the total upgrading with a highly covering ground coat, which can be lightly buffed, or ironed/embossed and further finished with our extensive range of acrylic/pu binders as required. On medium grade leathers may replace stucco with a highly covering/filling layer of Vie Compound V.

The main characteristics are:

  • retains a finer grain and break than other stuccos

  • dramatically upgrades and can even fill open scratches and ticks

  • gives high coverage

  • Has excellent Light and Heat resistant

Description: Vie Compound V is a specially designed product with a white paste like appearance. Vie Compound V is used as a Stucco sealer coat to cover minor defects, like brand-marks, thorn scratches etc on the leather surface so that they become less visible after finishing.It may be used after main stucco and buffing for very low grade materials. Vie Compound V can also be added to base coats to increase volume and therefore coverage and filling, especially suited for Roller coat application as the hollow encapsulated polymers may effect rheology and spraying levelness. Vie Compound is designed for upgrading all types of Low grade leathers, splits and Leather-board

Vie Compound V Application: Viecryl 93 is a fine particle extremely soft elastic Acrylic binder with excellent penetration properties. It can be used in Impregnation coats, Ground coats, or Base coats alone or with other suitable binders etc. Use on all types of Leather with other Acrylics, PUs and auxiliaries for general purpose and all round physical properties

  • Vie Compound V is applied without dilution on the leather surface by Roller Coat. It may also be applied by hand with a spatula, or for Leatherboard by a knife coating machine.

  • Care must be taken that all defects which should be covered on the surface

  • must be completely filled up with the product, a second coat may be applied to be sure. For very low grade apply first Vie Revive and Vie Revive RC, after drying, the leathers will be buffed to remove any surplus stucco. Articles would then be finished with Vie Compound V and further finished as required.

  • Vie Compound V can be coloured with Vie Microtint pigments or Viesol AQ dyes up to 10%.

Viecryl Compact NS

Solids content: tba

PH value: tba

Composition Viecryl Compact NS is an aqueous, extremely soft and stretchy, Compact Binder based on a combination very fine particle micro size acrylics with all necessary fillers, waxes, and other auxiliaries and is ready to use

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather even on super soft crust

  • gives good coverage, yet maintains an extremely natural look

  • Has good Light and Heat resistant

Viecryl Compact NS Application: Use on all types of Leather

Example Applications:

1. Garment Leather

Water 250 – 500 parts
Viecryl Compact NS 650 – 750 parts
Vietint pigments 250 – 75 parts

Spray x 1 – 2, kiss plate or iron 70 – 90oC, spray x 1 – 2 light to cover, spray top coat etc

Aniline look Shoe Upper/Fancy Goods Leathers

Water 250 – 350 parts
Viecryl 7 100 -150 parts
Viecryl Compact NS 400 – 500 parts
Vietint pigments 25 – 75 parts
Vie Lustre SS 25 – 75 parts

Spray x 1 – 2, plate, iron or Emboss 70 – 90 oC, spray x 1 – 2 light to cover, spray top coat etc

Viecryl Super Micro

Solids content: tba

PH value: tba

Composition Viecryl Super Micro is an aqueous, extremely soft and stretchy, Compact Binder based on a fine particle hybrid acrylic with all necessary fillers, waxes, and other auxiliaries and is ready to use. It has very good upgrading, and retains softness of crust.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather even on super soft crust

  • gives good coverage, yet maintains an extremely natural look

  • Has good Light and Heat resistant and a cold resistance of -30oC (Tg)

Viecryl Super Micro Applications: Use on all types of Leather where extreme cold resistance is required, particularly sports shoe nappas and garment leathers

Example Applications:

1. Garment Leather

Water 300 – 700 parts
Viecryl Super Micro 250 – 500 parts
Vie Microtint pigments 50 – 200 parts

Spray x 1 – 2, kiss plate or iron 70 – 90oC, spray x 1 – 2 light to cover, spray top coat etc

Aniline look Sports Shoe nappa

Water 250 – 350 parts
Viecryl 7 100 -150 parts
Viecryl Super Micro 350 – 500 parts
Vie Microtint pigments 50 – 200 parts

Spray x 1 – 2, plate, iron or Emboss 70 – 90 oC, spray x 1 – 2 light to cover, spray top coat etc

Viecryl 7

Solids content: 16%

PH value: tba

Composition Viecryl 7 is an aqueous, soft and elastic fine particle acrylic with outstanding penetration even on difficult crust

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • helps the whole finish to penetrate better

  • Has a low Tg and excellent Light and Heat resistant

Viecryl 7 Application: Use on all types of Leather with other Acrylics, Pu resins and auxiliaries to aid penetration and adhesion. Used alone with pigments and auxiliaries for Aniline looks

Example Applications:

Natural Look Garment or Softy Leathers for export market

Water 375 parts
Vie Super Penetrator 25 parts
Viepur Micro 50 parts
Vie Filler SFT 50 parts
Vie Wax 203 50 parts
Viecryl 7 100 parts
Viecryl Micro Compact 200 parts
Vietint Pigments 50 parts

Spray x 1 – 2 ,plate or iron 80oC, spray x 1 – 2 light top coat etc

Viecryl 94

Solids content: 30%

PH value: tba

Composition Viecryl 94 is an aqueous, soft, elastic acrylic with relatively low tack and good cold resistance

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • offers excellent embossing and plating properties

  • low tack and excellent Light and Heat resistant

Viecryl 94 Application: Use on all types of Leather with other Acrylics, Pus and auxiliaries for general purpose and all round physical properties

Example Applications:

1. Natural Aniline Softee Leathers for export market

Water 300 parts
Vie Super Penetrator LC 25 parts
Viecryl 7 100 parts
Vie Filler SFT 50 parts
Vie Wax 250 50 parts
Vie Lustre SS 75 parts
Viepur-01 50 parts
Viecryl 94 300 parts
Vie Tint Ultrafine Pigments 50 parts

Spray x 1 – 2 , plate or iron 80oC, spray x 1 – 2 light top coat etc

Viecryl Compact A-84

Solids content: tba

PH value: tba

Composition Viecryl Compact A-84 is an aqueous, medium soft, Compact Binder based on a combination of High Performance acrylics with all necessary fillers, waxes, and other auxiliaries to make it ready for use.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • gives high coverage, and excellent embossing properties

  • Has excellent Light and Heat resistant

Viecryl Compact A-84 Application: Use on all types of Leather

Example Applications:

1. High Cover Sofa Leather

Water 100 – 250 parts
Viecryl Compact A-84 650 – 750 parts
Vie Microtint or Viepaque pigments 100 -125 parts

Spray or Roller coat x 1 – 2, plate, iron or Emboss 80 – 90oC, spray x 1 – 2 light to cover, spray top coat etc

2. High Cover Shoe Upper/Fancy Goods Leathers

Water 250 parts
Viecryl 7 100 parts
Viecryl Compact A-84 500 – 600 parts
Vie Microtint or Viepaque pigments 50 – 100 parts

Spray or Roller coat x 1 – 2, plate, iron or Emboss 80 – 90 oC, spray x 1 – 2 light to cover, spray top coat etc

Viecryl Crax

Solids content: circa 40%

PH value: 8-10

Composition Viecryl Crax is an aqueous, self crosslinking, hard, tough, and non elastic acrylic with zero tack and outstanding water resistance and other physical properties. Viecryl Crax is mainly used for Aged, Second hand, or Crazed fashion effects.

The main characteristics are:

  • exhibits high fill

  • boosts dramatically all round physical properties

  • self crosslinking

  • good Light and Heat resistant can also be used to harden Top coats

Viecryl Crax Application: Use on all types of Leather with other Acrylics, Pu resins and auxiliaries to boost all round physicals, but especially Wet Physicals. Use alone or with other resin binders like Viepur-07, Viepur-35 or Viecryl-7 or Hard Waxes like Vie Crack Wax or Hard Proteins like Vie Lustre H for a variety of desirable fashion effects.

Example Applications:

Aged pigmented look

Water 200 parts
Vie Super Penetrator 25 parts
Viecryl-7 100 parts
Viepur-35 50 parts
Viecryl Crax 500 parts
Vie Crack Wax 100 parts
Vie Microtint Pigments 25 – 50 parts

Spray x 1 – 2, plate or iron 80oC, spray x 1 – 2 light, top coat etc, stake and mill to desired effect

Viecryl Eco Compact S

Solids content: 28%

PH value: 8-9

Composition Viecryl Eco Compact S is an aqueous, soft, Compact Binder based on a combination of acrylic co-polymers with all necessary fillers, waxes, and other auxiliaries to make it ready for use.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • gives very high filling and coverage of defects

  • Has good Light and Heat resistance

Viecryl Eco Compact S Application: Use on all types of Leather

Example Applications:

High Cover Softee Nappa Leather

Water 200 – 450 parts
Viecryl-7 100 parts
Viecryl Eco Compact S 450 – 700 parts
Vie Microtint pigments 100 parts

Spray or Roller coat x 1 – 2, plate, iron or Emboss 80 – 90oC, spray x 1 – 2 light to cover, spray top coat etc

Viecryl Ground LC

Solids content: tba

PH value: tba

Composition: Viecryl Ground LC is an Oil, Wax and Polymeric compacted product with a strong covering and filling effect.

Description: Viecryl Ground LC is a cream colored, viscous yet pourable liquid of high viscosity, which forms a soft, waxy, highly upgrading film

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • gives high coverage, and excellent embossing properties

  • Has excellent sealing effect of damaged grain

Viecryl Ground LC Application: Viecryl 93 is a fine particle extremely soft elastic Acrylic binder with excellent penetration properties. It can be used in Impregnation coats, Ground coats, or Base coats alone or with other suitable binders etc. Use on all types of Leather with other Acrylics, PUs and auxiliaries for general purpose and all round physical properties

Example Applications:

1. Preground for buffed upholstery leather or boot nappas

  • 0 – 100 p. Vietint pigment mix

  • 800 p. Viecryl Ground LC

  • 50 – 100 p. Water

  • 50 – 100 p. Viepur-35

  • 1 x forward roller coater, roto plate: 90° C/50 bar

2. Preground for full grain and corrected grain boot nappa and upholstery leather

  • 50 p. Vietint pigment mix

  • 300 p. Water

  • 400 p. Viecryl Ground LC

  • 200 p. Viecryl Super Compact

  • 50 p. Viepur-35

  • spray well 1 x, roto plate: 90° C/20 bar

3. Preground for full grain and grain-damaged leather

  • 50 – 100 p. Vietint pigment mix

  • 250 p. Viecryl Ground LC

  • 0 – 50 p. Vie Filler SFT (LC)

  • 300 p. Water

  • 50 p. Viecryl Micro IMP

  • 150 p. Viecryl-94

  • 50 – 100 p. Viepur-35

  • 50 – 100 p. Viepur-01

4. spray 1 x or 1 x forward roller coater

  • plate: 80 – 90° C/50 – 100 bar

Viecryl Micro Binder

Solids content: 20%

PH value: tba

Composition Viecryl Micro Binder is an aqueous, extremely soft and elastic micro-fine acrylic with outstanding penetration even on difficult crust.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • helps the whole finish to penetrate better

  • Has a low Tg and excellent Light and Heat resistant

Viecryl Micro Binder Application: Use on all types of Leather with other Acrylics, Pu resins and auxiliaries to aid penetration and adhesion. Used alone with pigments and auxiliaries for naked looks

Example Applications:

1. Natural Naked Look Garment or Softy Leathers for export market

Water 375 parts
Vie Super Penetrator 25 parts
Viepur Micro 50 parts
Vie Filler SFT 50 parts
Vie Wax 203 50 parts
Viecryl Micro Binder 400 parts
Vietint Ultrafine Pigments 50 parts

Spray x 1 – 2 ,plate or iron 80oC, spray x 1 – 2 light top coat etc

Viecryl Micro Compact

Solids content: tba

PH value: tba

Composition Viecryl Micro Compact is an aqueous, extremely soft and stretchy, Compact Binder based on a combination very fine particle micro size acrylics with all necessary fillers, waxes, and other auxiliaries and is ready to use.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather even on super soft crust

  • gives good coverage, yet maintains an extremely natural look

  • Has excellent Light and Heat resistant

Viecryl Micro Compact Application: Use on all types of Leather

Example Applications:

1) Garment Leather

Water 100 – 250 parts
Viecryl Micro Compact 650 – 750 parts
Vietint Ultrafine pigments 50 – 100 parts

Spray x 1 – 2, kiss plate or iron 70 – 90oC, spray x 1 – 2 light to cover, spray top coat etc

2) Aniline look Shoe Upper/Fancy Goods Leathers

Water 250 – 350 parts
Viecryl Micro Compact 500 – 600 parts
Vietint Ultrafine pigments 50 – 100 parts

Spray x 1 – 2, plate, iron or Emboss 70 – 90 oC, spray x 1 – 2 light to cover, spray top coat etc

Viecryl MPS

Solids content: 32%

PH value: tba

Composition Viecryl MPS is a micro-fine particle size, aqueous acrylic resin.

The main characteristics are:

  • retains a fine grain and break

  • excellent adhesion and grain tightening properties

  • helps the whole finish to penetrate better

  • very natural look and handle

Viecryl 93 Application:

  1. Viecryl MPS is normally used alone for impregnation on corrected grain leathers, simply use Water, Vie Super penetrator and Viecryl MPS in a ratio of 5:1:4 By using Viecryl MPS, excellent tightening of the grain can be achieved, but without excessive hardening of the crust, dependant on quantities applied.

  2. Viecryl MPS has even been found to successfully impregnate Full grain Leathers on absorbent crust, same formula as corrected grain is recommended

  3. Viecryl MPS can also be used as a general purpose Acrylic for Base coats of all types of Leathers but especially Garment, Softy Nappa etc

Viecryl Super Compact

Solids content: tba

PH value: tba

Composition Viecryl Super Compact is an aqueous, medium soft, Compact Binder based on a combination of High Performance acrylics with all necessary fillers, waxes, and other auxiliaries to make it ready for use.

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • gives high coverage, and excellent embossing properties

  • Has excellent Light and Heat resistant

Viecryl Super Compact Application: Use on all types of Leather

Example Applications:

1. High Cover Sofa Leather

Water 100 – 250 parts
Viecryl Super Compact 650 – 750 parts
Vietint or Viepaque pigments 100 parts

Spray or Roller coat x 1 – 2, plate, iron or Emboss 80 – 90oC, spray x 1 – 2 light to cover, spray top coat etc

2. High Cover Shoe Upper/Fancy Goods Leathers

Water 250 parts
Viecryl Micro Binder 100 parts
Viecryl Super Compact 500 – 600 parts
Vietint or Viepaque pigments 50 – 100 parts

Spray or Roller coat x 1 – 2, plate, iron or Emboss 80 – 90 oC, spray x 1 – 2 light to cover, spray top coat etc

Viecryl TG36

Solids content: 20%

PH value: tba

Composition Viecryl TG36 is an aqueous, soft, elastic acrylic with relatively low tack but outstanding cold resistance

The main characteristics are:

  • retains a fine grain and break

  • maintains the softness of the leather

  • gives properties similar to a Polyurethane

  • Has a Tg of -36oC and excellent Light and Heat resistant

Viecryl TG36 Application: Use on all types of Leather with other Acrylics, Pus and auxiliaries to boost Tg and other physicals

Example Applications:

1. Natural Aniline Look Garment or Softee Leathers for export market

Water 350 parts
Vie Super Penetrator 25 parts
Viepur Micro 50 parts
Vie Filler SFT 50 parts
Vie Wax 203 50 parts
Viecryl TG36 400 parts
Vie Tint Ultrafine Pigments 50 parts

Spray x 1 – 2 , plate or iron 80oC, spray x 1 – 2 light top coat etc

Viecryl XL97

Solids content: tba

PH value: tba

Composition Viecryl XL97 is an aqueous, self crosslinking, medium hard, tough, and elastic acrylic with very low tack and outstanding water resistance and other physical properties

The main characteristics are:

  • exhibits high fill

  • boosts dramatically all round physical properties

  • self crosslinking

  • excellent Light and Heat resistant can also be used to soften Top coats

Viecryl XL97 Application: Use on all types of Leather with other Acrylics, Pu resins and auxiliaries to boost all round physicals, but especially Wet Physicals.

Example Applications:

1. High Performance Sports Leathers for export market

Water 200 parts
Vie Super Penetrator 25 parts
Viepur Micro 100 parts
Viepur Flow 100 parts
Viecryl XL97 75 parts
Vie Filler SFT 50 parts
Vie Wax 203 50 parts
Viecryl TG36 300 parts
Viepaque Pigments 100 parts

Spray x 1 – 2, plate or iron 80oC, spray x 1 – 2 light, top coat etc

Viepur-04

Solids content: 12%

PH value: 7-8

Composition Viepur-04 is an Aqueous modified Fine particle Aliphatic Polycarbonate Polyurethane dispersion to be used as a base, intermediate base or Top coat on glossy fashion Leathers without over- loading the grain. Being based on first class Polycarbonate Polyurethane it has outstanding physical properties and is hydrolysis resistant for a long lasting life

The main characteristics are:

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with Vielink AZ

  • good Light and Heat resistance, NC and Amine free

  • good hydrolysis resistance

Viepur-04 Application: Use on all types of Leathers where high gloss is required, while maintaining a natural look and feel. It can be used in base coats, or intermediate base coats to any proportion or used as a Top coat by diluting up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint Ultrafine pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Vielink AZ

Example Applications:

Top coat for high Gloss Shoe Upper, Handbag and Fancy goods Leathers:

Viepur-04 500 parts
Water 250 – 350 parts
Vie Feel SS etc 5 – 15 parts
Vielink AZ 1 2 – 10 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

Viepur Top AT

Solids content: 32%

PH value: 7-8

Composition Viepur Top AT is an Aqueous Aliphatic Polycarbonate type Polyurethane dispersion with necessary additives to be used as a Top coat on glossy fashion Leathers, Sofa and even Automotive without over- loading the grain. It shows good hydrolysis resistance to facilitate a long Life for the Leather article

The main characteristics are:

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with aziridines or isocyanate

  • excellent Heat and Light resistance, good hydrolysis resistance

Viepur Top AT: Use on all types of Leathers where high gloss is required, while maintaining a natural look and feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Aziridine or Isocyanate crosslinkers

Example Applications:

Top coat for high Gloss Shoe, Handbag and Fancy goods Leathers:

Viepur Top AT 500 parts
Water 250 – 350 parts
Vie Feel RL 10 – 25 parts
Vielink AZ 2 – 10 parts
Vie Top 137 50 – 100 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

Top coat for Patent Leathers

Viepur Top APT 900 parts
Water 50 parts
Vie Feel RL 10 – 25 parts
Vielink AZ 6 – 12 parts
Vie Paste RM 0 – 30 parts to adjust viscosity

Roller Coat or Spray x 2 wet, dry well, Mill, Stake, Toggle. Iron or Hot Plate 90 – 120oC low pressure as required depending on fashion effect required

Vielac W-99

Solids content: 17%+-1

PH value: circa 5 +-0.5

Composition Vielac W-99 is a soft concentrated water dilutable nitrocellulose emulsion lacquer

The main characteristics are:

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • . for higher physicals can be crosslinked with Vielink AZ

Vielac W-99 Application: Vielac W-99 is a milky-white, highly concentrated emulsion of low viscosity, which produces a soft, clear film with a medium gloss. The product gives a very good filling and a pleasant touch. Vielac W-99 is special in its good plating behaviour at higher temperatures, good embossability, low tackiness when used as intermediate lacquer for embossing and by its good millability retaining a super natural grain break. Vielac W-99 is compatible with many additives. Due to its good filling properties, Vielac W-99 also provides a very even surface to the leather. Can be crosslinked with 1-2% Vielink AZ if higher physicals are required

Example Applications:

1. Top coat for Garment, Shoe Upper, Handbag and Fancy goods Leathers:

Vielac W-99 500 parts
Water 500 parts
Vie Feel SS etc 5 – 25 parts
Vielink AZ 2 – 10 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

2. Waxy Top Coat for Garment and Softee Nappa:

Water 450 parts
Vie Catwax 50 parts
Vielac W-99 500 parts

Adjust feel as required with Vie Feel 251 and 760

Vie Top 137

Solids content: tba

PH value: tba

Composition Vie Top 137 is an Acrylic Modified Protein for all types of Leathers

The main characteristics are:

  • Eliminates Tack and Increases Gloss in Base and Top coats

  • Gives a Natural Protein feel to the Finish

  • Has much improved Physicals compared to Natural Proteins

  • Can be used with Crosslinker as a stand-alone Top coat where a natural look and feel is required

Vie Top 137 Application: Used mainly on Fancy Goods Leathers in or over the Top coat to give a Natural Protein Look and Feel

Example Applications:

  1. Add 50 – 300 parts per kg in aqueous Top Coats for Fancy Goods Leathers

  2. Use as an over-spray Feel and Gloss coat 250 – 500 parts Vie Top 137 with 250 – 750 parts Water and 5 – 10 parts Vie Feel AR and spray light as required, Iron or Hot Plate 100oC +

  3. Replace 50 – 100 % of Natural Proteins in Base coat for Imitation Glazed Finishes where improved Water resistance or Wet Properties are required

Vielac W-88

Solids content: 20%

PH value: circa 7 +-0.5

Composition Vielac W-88 is a concentrated water dilutable nitrocellulose emulsion lacquer with special heat resistant plasticizers

The main characteristics are:

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with Vielink AZ

  • excellent heat resistant properties, can withstand over 200oC

Vielac W-88 Application: Vielac W-88 is a milky-white, highly concentrated emulsion of low viscosity, which produces a soft, clear film with a medium gloss. The product gives a very good filling and a pleasant touch. Vielac W-88 is special in its good plating behaviour at higher temperatures, good embossability, low tackiness when used as intermediate lacquer for embossing and by its good millability retaining a super natural grain break. Vielac W-88 is compatible with many additives. Due to its good filling properties, Vielac W-88 also provides a very even surface to the leather. With special heat resistant plasticizers it is highly recommended for hot stamping, imitation glazed, polishable and burnishable leathers, waxed and oiled leathers, as well as full vegetable and heavy vegetable type leathers. Can be crosslinked with 1-2% Vielink AZ if higher physicals are required

Example Applications:

1. Top coat for high Gloss Shoe Upper, Handbag and Fancy goods Leathers:

Vielac W-88 500 parts
Water 500 parts
Vie Feel SS etc 5 – 25 parts
Vielink AZ 2 – 10 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

Vielac WS-218

Solids content: 26%

PH value: circa 7 +-0.5

Composition Vielac WS-218 is a highly concentrated solvent or water dilutable nitrocellulose lacquer

The main characteristics are:

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with Vielink AZ

  • water or solvent dilutable reducing inventory

Vielac WS-218 Application: Vielac WS-218 is a viscous transparent, highly concentrated Nitrocellulose lacquer, which produces a medium hard, clear film with a high gloss. The product gives a very good filling and a pleasant touch. Vielac WS-218 exhibits good plating behaviour at temperatures of up to 120oC, also has good embossability, low tackiness when used as intermediate lacquer for embossing and by its good millability retaining a super natural grain break. Vielac WS-218 is compatible with many additives. Due to its good filling properties, Vielac WS-218 also provides a very smooth and well filled surface to the leather. Use with water for use as intermediate or top lacquer for medium shine or with Glycols or Acetates for Ultra high gloss top lacquers. Can be crosslinked with 1-2% Vielink AZ if higher physicals are required. Modify feel with Vie Feel range as required

Example Applications:

1. Intermediate lacquer coat for high Gloss Shoe Upper, Handbag and Fancy goods Leathers:

Vielac WS-218 500 parts
Water 250 parts mix well and add
Water 250 – 750 parts mix well

Spray x 1 Emboss, Iron or Hot Plate 70 – 120oC as required

2. Top Lacquer for Shoe or Bag Leathers:

Vielac WS-218 500 parts
Methoxy Propanol 250 parts
Butyl Acetate 750 parts

Spray x 1 – 2 Iron or Hot Plate 90oC

Vielac Zero

Solids content: circa 13%

PH value: 8 +-0.5

Composition Vielac Zero is a new concept water dilutable nitrocellulose free emulsion lacquer with no external plasticizers.

The main characteristics are:

  • Zero N.C, Zero external plasticizers, zero restricted substances

  • Zero flashpoint, zero fire risk, zero machinery explosion risk

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with Vielink AZ

  • good heat resistant properties

Vielac Zero Application: Vielac Zero is a milky-white, emulsion of low viscosity, which produces a soft, clear film with a medium gloss. The product gives a very good filling and a pleasant touch. Vielac Zero is special in its good plating behaviour at higher temperatures, good embossability, low tackiness when used as intermediate lacquer for embossing and by its good millability retaining a super natural grain break. Vielac Zero is compatible with many additives. Due to its good filling properties, Vielac Zero also provides a very even surface to the leather. Being Nitrocellulose free and without external plasticizers it is suitable for any types of leathers. Can be crosslinked with 1-2% Vielink AZ if higher physicals are required. Suitable for articles of Leather in combination with PVC etc without possibility of plasticizer migration which causes yellowing.

Example Applications:

1. Top coat for high Gloss Shoe Upper, Handbag and Fancy goods Leathers:

Vielac Zero 500 parts
Water 250 parts
Vie Feel SS etc 5 – 25 parts
Vielink AZ 2 – 10 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

2. Lacquer for application onto Shoes, Bags etc:

Vielac Zero 100% spray without dilution dry with or without heat

Viepur Top APT

Solids content: circa 35%

PH value: tba

Composition: Viepur Top APT is an Aqueous Aliphatic Polycarbonate type Polyurethane dispersion with necessary additives to be used as a Top coat on glossy fashion Leathers, Sofa and even Automotive without over- loading the grain. It shows good hydrolysis resistance to facilitate a long Life for the Leather article

The main characteristics are:

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with aziridines or isocyanate

  • excellent Heat and Light resistance, good hydrolysis resistance

Viepur Top APT Application: Use on all types of Leathers where high gloss is required, while maintaining a natural look and feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Aziridine or Isocyanate crosslinkers

Example Applications:

1. Top coat for high Gloss Shoe, Handbag and Fancy goods Leathers:

Viepur Top APT 500 parts
Water 250 – 350 parts
Vie Feel RL 10 – 25 parts
Vielink AZ 2 – 10 parts
Vie Top 137 50 – 100 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

2. Top coat for Patent Leathers

Viepur Top APT 900 parts
Water 50 parts
Vie Feel RL 10 – 25 parts
Vielink AZ 6 – 12 parts
Vie Paste RM 0 – 30 parts to adjust viscosity

Spray x 1 Mill, Stake, Toggle. Iron or Hot Plate 90 – 120oC low pressure

Viepur Top DV Matt

Solids content: circa 25%

PH value: tba

Composition Viepur Top DV Matt is a Dull Aqueous Aliphatic type Polyurethane dispersion with necessary additives to be used as a Dull Top coat for virtually any substrate. It shows good hydrolysis resistance to facilitate a long Life for the coating. Based on state of the art Polymeric matting technology it gives a dull appearance yet with a pleasant soft feel. When crosslinked with the addition of 1 – 2 % Vielink AZ it hardens to a high level of flexibility, adhesion and scuff resistance as well as good all round properties. NB Full crosslinking can take up to 48 hours.

The main characteristics are:

  • exhibits a high level of mattness yet with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with aziridines or isocyanate

  • excellent Heat and Light resistance, good hydrolysis resistance

Viepur Top DV Matt Application: Use on all virtually all substrates where a dull look is required, while maintaining a natural soft feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Aziridine or Isocyanate crosslinkers. Vielink AZ is highly recommended.

Example Applications:

1. Repair coated rubber sheets:

Viepur Top DV Matt 1000 parts
Water 80 -180parts
Vielink AZ 20 parts ) Premix before adding Viepur Top

Spray x 1 – 2 suggest spray first coat lightly if rubber sheet has silicone and reticulation occurs, second spray will flow out well

2. Top coat for Automotive Leathers

Viepur Top APT Gloss 0 -1000 parts ) Total 1000 parts of gloss
Viepur Top DV Dull 1000 – 0 parts ) and/or dull
Water 50 parts
Vie Feel RL 10 – 25 parts
Vielink AZ 10 – 20 parts
Vie Paste RM 0 – 30 parts to adjust viscosity

Spray x 1 Mill, Stake, Toggle. Iron or Hot Plate 90 – 120oC low pressure

Viepur Top Elegante

Solids content: tba

PH value: tba

Composition Viepur Top Elegante is an Aqueous Aliphatic Polyurethane dispersion with necessary additives to be used as a Top coat on glossy fashion Leathers without over- loading

The main characteristics are:

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with aziridines or isocyanate

  • excellent Light and Heat resistance

Viepur Top Elegante Application: Use on all types of Fashion Leathers where a natural high gloss is required, while maintaining a natural look and feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vie Tint pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Aziridine or Isocyanate crosslinkers

Example Applications:

1. Top coat for high Gloss Handbag and Fancy goods Leathers:

Viepur Top Elegante 500 parts
Water 250 – 500 parts
Vie Feel AR 3 – 8 parts
Vielink AZ 5 – 10 parts
Vie Top 137 50 – 100 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

2. Top coat for elegant shine Fancy goods Leathers

Viepur Top Elegante 600 parts
Water 400 parts
Vie Feel AR 0 – 5 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

Viepur Top FL-01 Matt

Solids content: circa 20%

PH value: tba

Composition Viepur Top FL-01 Matt is an Aqueous modified Aliphatic Polyurethane dispersion with necessary additives to be used as a Top coat on Medium Gloss – Matt fashion Leathers without over- loading the grain

The main characteristics are:

  • exhibits high degree of mattness with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with Vielink AZ

  • good Light and Heat resistance, NC and Amine free

Vielac WS-218 Application: Use on all types of Leathers where medium gloss – Mattness is required, while maintaining a natural look and feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Vielink AZ. Use in Combination with Viepur Top FL-01 (Gloss)

Example Applications:

1. Intermediate lacquer coat for high Gloss Shoe Upper, Handbag and Fancy goods Leathers:

Viepur Top FL-01 250 parts
Viepur Top FL-01 Matt 250 parts
Water 250 – 350 parts
Vie Feel SS etc 5 – 15 parts
Vielink AZ 2 – 10 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

2. Top coat for Matt Leathers:

Viepur Top FL-01 Matt 500 parts
Water 250 – 500 parts
Vie Feel SS etc 5 – 15 parts
Vielink AZ 2 – 10 parts

Viepur Top FL-01

Solids content: 20%

PH value: tba

Composition Viepur Top FL-01 is an Aqueous modified Aliphatic Polyurethane dispersion with necessary additives to be used as a Top coat on glossy fashion Leathers without over- loading the grain

The main characteristics are:

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with Vielink AZ

  • good Light and Heat resistance, NC and Amine free

Viepur Top FL-01 Application: Use on all types of Leathers where high gloss is required, while maintaining a natural look and feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint Ultrafine pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Vielink AZ

Example Applications:

1. Top coat for high Gloss Shoe Upper, Handbag and Fancy goods Leathers:

Viepur Top FL-01 500 parts
Water 250 – 350 parts
Vie Feel SS etc 5 – 15 parts
Vielink AZ 2 – 10 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

Viepur Top FL-02 Matt

Solids content: circa 20%

PH value: tba

Composition Viepur Top FL-02 Matt is a Dull Aqueous modified Aliphatic Polyurethane dispersion with necessary additives to be used as a Top coat on all types of Leathers without over- loading the grain

The main characteristics are:

  • exhibits high dullness without whitening, hardening or raspiness

  • gives good all round physical properties

  • for higher physicals can be crosslinked with Vielink AZ

  • good Light and Heat resistance, NC and Amine free

Viepur Top FL-02 Application: Use on all types of Leathers where a high level of Dullness is required, while maintaining a natural look and feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint Ultrafine pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Vielink AZ. Shows excellent inter-coat adhesion and is highly suitable as a Milling Season or intermediate lacquer. Use in any proportion with its glossy counterpart Viepur Top FL-02

Example Applications:

1. Top coat for Matt Shoe Upper, Handbag and Fancy goods Leathers:

Viepur Top FL-02 Matt 500 parts
Water 250 – 350 parts
Vie Feel SS etc 5 – 25 parts
Vielink AZ 2 – 10 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

2) Dull Milling Season/Intermediate Lacquer for Sofa Leathers:

Viepur Topl FL-02 200 parts
Viepur Top FL-02 Matt 300 parts
Water 500 – 1000 parts

Spray x 1 Mill, Stake etc

Viepur Top FL-02

Solids content: 20%

PH value: tba

Composition Viepur Top FL-02 is an Aqueous modified Aliphatic Polyurethane dispersion with necessary additives to be used as a Top coat on glossy fashion Leathers without over- loading the grain

The main characteristics are:

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with Vielink AZ

  • good Light and Heat resistance, NC and Amine free

Viepur Top FL-02 Application: Use on all types of Leathers where high gloss is required, while maintaining a natural look and feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint Ultrafine pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Vielink AZ. Shows excellent inter-coat adhesion and is highly suitable as a Milling Season or intermediate lacquer

Example Applications:

1. Top coat for high Gloss Shoe Upper, Handbag and Fancy goods Leathers:

Viepur Top FL-02 500 parts
Water 250 – 350 parts
Vie Feel SS etc 5 – 15 parts
Vielink AZ 2 – 10 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

2. Milling Season/Intermediate Lacquer for Sofa Leathers:

Viepur Topl FL-02 500 parts
Water 500 – 1000 parts

Spray x 1 Mill, Stake etc

Viepur Top GM

Solids content: 20%

PH value: tba5

Composition Viepur Top GM is an Aqueous Aliphatic Polyurethane dispersion with necessary additives to be used as a Matt Top coat on all types of fashion Leathers without over- loading the grain

The main characteristics are:

  • exhibits high mattness with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with aziridines or isocyanate

  • excellent Light and Heat resistance, no white break

Viepur Top GM Application: Use on all types of Leathers where a very dull finish is required, while maintaining a natural look and feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint Ultrafine pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Aziridine or Isocyanate crosslinkers. It is normally used in conjunction with Viepur Top GP at any ratio and is seldom used alone as it is extremely dull and alone may swing the shade too much

Example Applications:

1. Top coat for high very dull Handbag and Fancy goods Leathers:

Viepur Top GP 100 parts
Viepur Top GM 400
Water 400 parts
Vie Feel AR 3 – 8 parts
Vielink AZ 2 – 10 parts

Spray x 1 – 2 Iron or Smooth Plate 70 oC low pressure

2. Top coat for Satin Gloss Shoe upper Leathers

Viepur Top GP 300 parts
Viepur Top GM 300 parts
Water 400 parts
Vie Feel AR/SW etc 2 – 5 parts
Vielink AZ 5 – 12 parts

Spray x 1 – 2 Iron or Hot Plate 70 – 80oC low pressure

Viepur Top GP

Solids content: circa 16%

PH value: tba

Composition Viepur Top GP is an Aqueous Aliphatic Polyurethane dispersion with necessary additives to be used as a Top coat on glossy fashion Leathers without over- loading the grain

The main characteristics are:

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with aziridines or isocyanate

  • excellent Light and Heat resistance

Viepur Top GP Application: Use on all types of Leathers where high gloss is required, while maintaining a natural look and feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint Ultrafine pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Aziridine or Isocyanate crosslinkers

Example Applications:

1. Top coat for high Gloss Handbag and Fancy goods Leathers:

Viepur Top GP 500 parts
Water 250 – 350 parts
Vie Feel AR 3 – 8 parts
Vielink AZ 2 – 10 parts
Vie Top 137 50 – 100 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

2. Top Lacquer for Shoe or Bag Leathers:

Viepur Top GP 600 parts
Water 400 parts
Vie Feel AR/SW etc 2 – 5 parts
Vielink AZ 5 – 12 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

Viepur Top HP

Solids content: tba

PH value: tba

Composition Viepur Top HP is an Aqueous Aliphatic Polyurethane dispersion with necessary additives to be used as a Top coat on glossy high performance Leathers

The main characteristics are:

  • exhibits high gloss and clarity with all round good physicals

  • used on shoe upper, Sofa, and any leather where high physicals are

  • required
  • for even higher physicals can be crosslinked with aziridines or

  • isocyanate
  • excellent Light and Heat resistance

Viepur Top HP Application: Use on all types of Leathers where a high gloss and high physicals are required. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint Ultrafine pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Aziridine or Isocyanate crosslinkers

Example Applications:

1. Top coat for high Gloss Shoe Upper Leathers::

Viepur Top HP 600 parts
Water 250 – 400 parts
Vie Feels 3 – 15 parts
Vielink AZ 5 – 12 parts

Spray x 1 – 2 Iron or Hot Plate 80 – 100oC low pressure

Viepur Top SX Matt

Solids content: 20%

PH value: tba

Composition: Viepur Top SX Matt is a Dull Aqueous Aliphatic Polycarbonate type Polyurethane dispersion with necessary additives to be used as a Top coat on all types of fashion Leathers, Sofa and even Automotive without over- loading the grain. It shows good hydrolysis resistance to facilitate a long Life for the Leather article

The main characteristics are:

  • exhibits high level of dullness without whitening, hardening or raspiness

  • gives good all round physical properties

  • for higher physicals can be crosslinked with aziridines or isocyanate

  • excellent Heat and Light resistance, good hydrolysis resistance

Viepur Top SX Matt Application: Use on all types of Leathers where dullness is required, while maintaining a natural look and feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint Ultrafine pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Aziridine or Isocyanate crosslinkers. Use in any proportion with its glossy counterpart Viepur Top SX

Example Applications:

1. Top coat for Super Matt Shoe, Handbag and Fancy goods Leathers:

Viepur Top SX Matt 500 parts
Water 250 – 350 parts
Vie Feel RL 10 – 25 parts
Vielink AZ 2 – 10 parts
Vie Top 137 50 – 100 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

2. Dull Top coat for elegant Sofa Leathers

Viepur Top SX Matt 400 parts
Viepur Top SX 200 parts
Water 400 parts

Spray x 1 – 2 Iron or Hot Plate 90oC

Viepur Top SX

Solids content: 20%

PH value: tba

Composition Viepur Top SX is an Aqueous Aliphatic Polycarbonate type Polyurethane dispersion with necessary additives to be used as a Top coat on glossy fashion Leathers, Sofa and even Automotive without over- loading the grain. It shows good hydrolysis resistance to facilitate a long Life for the Leather article

The main characteristics are:

  • exhibits high gloss and clarity with a natural look and feel

  • gives good all round physical properties

  • for higher physicals can be crosslinked with aziridines or isocyanate

  • excellent Heat and Light resistance, good hydrolysis resistance

Viepur Top SX Application: Use on all types of Leathers where high gloss is required, while maintaining a natural look and feel. It can be diluted up to 1: 1 with water and further modified with Vie Feel agents to give a variety of feels, also can be tinted with small amounts of Vietint Ultrafine pigments or Viesol LD dyes, and for even higher physicals may be crosslinked with Aziridine or Isocyanate crosslinkers

Example Applications:

1. Top coat for high Gloss Shoe, Handbag and Fancy goods Leathers:

Viepur Top SX 500 parts
Water 250 – 350 parts
Vie Feel RL 10 – 25 parts
Vielink AZ 2 – 10 parts
Vie Top 137 50 – 100 parts

Spray x 1 – 2 Iron or Hot Plate 90 – 120oC low pressure

2) Top coat for elegant shine Sofa Leathers

Viepur Top SX 600 parts
Water 400 parts
Vie Feel RL/SW(N) etc 10 – 25 parts
Vielink AZ 6 – 12 parts

Spray x 1 Mill, Stake, Toggle. Iron or Hot Plate 80 – 110oC low pressure

Vie Oil PS

Solids content: 100% +-2

PH value: 5-6

Composition: Vie Oil PS is a concentrated self emulsifiable blend of vegetable and synthetic oils.

Description: Vie Oil PS is a turbid, semi translucent liquid of medium viscosity, which is designed to be used without dilution for Pad or Roller coat application or diluted with water for Spray applications. The product is specially developed for glazed, polish, resin and pull-up-finishes. Vie Oil PS shows following properties

The main characteristics are:

  • Softening additive for Proteins, and Waxes such as Vie Antik Waxes

  • For Polished finishes as a pre-ground to even out absorbency of the crust

  • To improve repolishability and increases gloss

  • Medium to strong Pull up effect, when applied heavily without dilution

Vie Oil PS Application:

Vie Oil PS is used alone or in combination with suitable protein binders in polish or pre-grounds on full grain or buffed leathers. The product improves considerably inferior leathers (Upgrading). Vie Oil PS evens out the absorbency of the crusts and keeps a fine grain break. For pull-up articles, Vie Oil PS is applied undiluted on the crust usually by roller coater, it can also be used in conjunction with Vie Antik Wax 30 or 40 for Fashionable Waxed Pull up effects.

Example Applications:

1. High Gloss Pull up Corrected grain leathers:

  • 100% Vie Oil PS Roller coat x 1 -2 times

  • Leave as long as possible preferably overnight

  • Polish and/or Plate/Iron 100oC or higher

  • Finish as required

2. High Gloss Full Grain Pull up Leather:

  • Dilute 1:1 with water spray x 1 -2 times

  • Leave as long as possible preferably overnight

  • Polish and/or Plate/Iron 90-120oC

  • Finish as required

3. Polish ground for Imitation Glazed Leathers:

  • 50 parts Vie Super penetrator LC

  • 625 parts Water

  • 100 parts Vie Lustre H

  • 75 parts Vie Oil PS

  • 50 parts Viepur Micro

  • 100 parts Vie Lustre SS

  • spray 1 x, polish on a felt

4. Base coat:

  • 450 parts Water

  • 25 parts Vie Super penetrator

  • 100 parts Vie Lustre H

  • 50 parts Viecryl TG36

  • 50 parts Viecryl XL97

  • 50 parts Vie Top 137

  • 50 parts Viepur Flow

  • 25 parts Vietint Ultrafine pigments

  • spray x 2 – 3 light

Top coat

  • 500 parts Viepur Top FL-01

  • 435 parts Water

  • 50 parts Vie Lustre H

  • 10 parts Vlelink AZ

  • 5 parts Viefeel DW

  • spray x 1 – 2 , Iron or Kiss plate 100 – 120° C

Vie OIl L

Solids content: 100% +-2

PH value: N/A

Composition: Vie Oil L is a concentrated blend of vegetable and aromatic mineral spirits with added aroma.

Description: Vie Oil L is a liquid, semi translucent liquid of medium viscosity, which is designed to be used without dilution for Pad, Roller coat or spray application. The product is specially developed for a natural glazed, polished look. Vie Oil L shows following properties

The main characteristics are:

  • Softening additive for Semi or Vegetable Leathers with a natural long lasting shine

  • For Polished finishes as a pre-ground to even out absorbency of the crust, spray neat

  • To improve repolishability and increases gloss of unfinished Leathers

  • Low to medium Pull up effect, when applied heavily without dilution

Vie Oil L Application:

Vie Oil L is usually used alone for polish or pre-grounds on full grain or buffed leathers. The product improves considerably inferior leathers (Upgrading). Vie Oil L evens out the absorbency of the crusts and keeps a fine grain break. For pull-up articles, Vie Oil L is applied undiluted on the crust usually by roller coater, Sponge, Pad or Spray. Leathers can be polished after leaving a few hours, using machine or by hand with a soft cotton or wool cloth

Example Applications:

1. High Gloss Pull up Corrected grain leathers:

  • 100% Vie Oil L Roller coat x 1 -2 times

  • Leave as long as possible preferably overnight

  • Polish and/or Plate/Iron 100oC or higher

  • Finish as required

2. High Gloss Full Grain Pull up Leather:

  • Spray x 1 -2 times neat

  • Leave as long as possible preferably overnight

  • Polish and/or Plate/Iron 90-120oC

  • Finish as required

3. Polish ground for Imitation Glazed Leathers:

  • Spray x 1 neat, leave overnight

  • polish on a felt or stone

  • Finish with adhesion coat, base and top and hot iron 120oC

Vie Oil G

Solids content: 36%+-2

PH value: 7-9

Composition: Vie Oil G is a water dilutable Oil emulsion in cream form with medium darkening and pull up effect for most types of Leathers, due to its vegetable base it is extremely glossy, and may also be used as an additive in glazed, polished or high gloss casein based finishes. Being a cream by nature it is highly suitable for Roller coat application, it may be diluted by adding water into the cream, stirring and well and further dilution afterwards as required.

The main characteristics are:

  • Can be sprayed or Roller coated without heat

  • Reduces VOC emissions to zero

  • Natural Oily silky feel

  • Medium to strong Pull up effect

Vie Oil G Application: Used Neat or diluted with Water

Example Applications:

1. Natural Pull up with a pleasant Oily/Silky feel

  • 00% Vie Oil G

  • Pad or Roller coat as required, Plate etc

2. Cyclone type Pull up Leathers:

  • 100% Vie Oil G

  • Pad or Roller coat as required, Finish with adhesion coat, base coat and Top coat, Sandblast plate 90oC (Ask Vie Chemie for Technical advice)

3. Additive to Casein finishes 5-10% dilute with 20% water, stir well and add another 30% water before adding to other materials in the finish formulation like Casein, PU etc

Vie Oil 630

Solids content: 100% +-2

PH value: 5-6

Composition: Vie Oil 630 is a concentrated self emulsifiable blend of vegetable and synthetic oils.

Description: Vie Oil 630 is a turbid, semi translucent liquid of medium viscosity, which is designed to be used without dilution for Pad or Roller coat application or diluted with water for Spray applications. The product is specially developed for glazed, polish, resin and pull-up-finishes. Vie Oil 630 shows following properties.

The main characteristics are:

  • Softening additive for Proteins, and Waxes such as Vie Antik Waxes

  • For Polished finishes as a pre-ground to even out absorbency of the crust

  • To improve repolishability and increases gloss

  • Medium to strong Pull up effect, when applied heavily without dilution

Vie Oil 630 Application: Vie Oil 630 is used alone or in combination with suitable protein binders in polish or pre-grounds on full grain or buffed leathers. The product improves considerably inferior leathers (Upgrading). Vie Oil 630 evens out the absorbency of the crusts and keeps a fine grain break. For pull-up articles, Vie Oil 630 is applied undiluted on the crust usually by roller coater, it can also be used in conjunction with Vie Antik Wax 30 or 40 for Fashionable Waxed Pull up effects.

Example Applications:

1. High Gloss Pull up Corrected grain leathers:

  • 100% Vie Oil 630 Roller coat x 1 -2 times

  • Leave as long as possible preferably overnight

  • Polish and/or Plate/Iron 100oC or higher

Vie Oil 383

Solids content: 96%+-2

PH value: 7-8

Composition: Vie Oil 383 is a water dilutable Oil with medium darkening and pull up effect for most types of Leathers .

The main characteristics are:

  • Can be sprayed or Roller coated without heat

  • Reduces VOC emissions to zero

  • Natural feel

  • Medium to strong Pull up effect

Vie Oil 383 Application: Used Neat or diluted with Water

Example Applications:

1. Natural Pull up with a pleasant natural feel

  • 100% Vie Oil 383

  • Spray, Pad or Roller coat as required, Plate etc

2. Cyclone type Pull up Leathers:

  • 100% Vie Oil 383

  • Spray, Pad or Roller coat as required, Finish with adhesion coat, base coat and Top coat, Sandblast plate 90oC (Ask Vie Chemie for Technical advice)

Vie Hot Wax CN

Solids content: 100%

PH value: n/a

Composition: Vie Hot Wax CN is a VOC free Hot Wax designed to be used alone or with Hot Melt Oils on USA style Leathers and European Fashion Pull ups. It is mostly composed of natural waxes and is from renewable sources.

The main characteristics are:

  • Used on Semi or Full Veg leathers for strong Pull up effect with a strong gloss

  • Used on USA style Leathers like Crazy Horse for strong Pull up effect

  • Reduces VOC emissions to zero

  • Ecologically friendly and virtually no odour, no tendency to spew in cold weather

  • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Waxy Natural feel

Vie Hot Wax CN G Application: Used with almost all types of Oils and Waxes used on Hot Roller coaters to give a long lasting strong Pull up effect.

Example Applications:

  • Melt Hot Wax CN at about 80oC, and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  • Can be used 2:1 to 1:1 with Vie Hot Oil Extender, for Lower strength Pull Up effects and more drain back, pour or pump onto Roller coater, use 70-80oC

  • Can be used with Other Vie Oils like Vie Hot Oil SS230 if more waxy effect is required

  • Can be used with Vie Hot Oil WP for Maeser or W/P Leathers

  • Can be used with Vie Hot Oil 210 or 212 etc for a variety of Pull up effects

Vie Grease Oil DK

Solids content: 96%+-2

PH value: 7-9

Composition: Vie Grease Oil DK is a water dilutable Oil with strong darkening and pull up effect for most types of Leathers .

The main characteristics are:

  • Can be sprayed or Roller coated without heat

  • Reduces VOC emissions to zero

  • Natural Oily/greasy feel

  • Medium to strong Pull up effect

Vie Grease Oil DK Application: Used Neat or diluted with Water

Example Applications:

1. Natural Pull up with a pleasant Oily/Greasy feel

  • 100% Vie Grease Oil DK

  • Spray, Pad or Roller coat as required, Plate etc

2. Cyclone type Pull up Leathers:

  • 100% Vie Grease Oil DK

  • Spray, Pad or Roller coat as required, Finish with adhesion coat, base coat and Top coat, Sandblast plate 90oC (Ask Vie Chemie for Technical advice)

k

Vie Grease Oil RK

Solids content: 100%

PH value: n/a

Composition: Vie Grease Oil RK is a water dilutable Oil with medium darkening and pull up effect for most types of Leathers

The main characteristics are:

  • Can be sprayed or Roller coated without heat

  • Reduces VOC emissions to zero

  • Natural Oily/greasy feel

  • Medium to strong Pull up effect

Vie Grease Oil RK Application: Used Neat or diluted with Water

Example Applications:

1. Natural Pull up with a pleasant Oily/Greasy feel

  • 100% Vie Grease Oil RK

  • Spray, Pad or Roller coat as required, Plate etc

2. Cyclone type Pull up Leathers:

  • 100% Vie Grease Oil RK

  • Spray, Pad or Roller coat as required, Finish with adhesion coat, base coat and Top coat, Sandblast plate 90oC (Ask Vie Chemie for Technical advice)

Vie Hot Oil 210

Solids content: 100%

PH value: n/a

Composition: Vie Hot Oil 210 is a VOC free Light Oil designed to be used alone or with Hot melt waxes for USA style Pull up Leathers.

Description: Vie Hot Oil 210 is a light yellowish-brown, solvent-free oil. When applied to corrected or full grain leathers prior to finishing, it provides an excellent pull-up with a light to medium strong surface darkening after hot plating. This oil is exceptionally useful for upgrading leathers as it does not highlight defects

The main characteristics are:

  • Extends Hot Oils and Waxes on roller coaters, can be used also for Light to Strong Oil Pull up effects

  • Reduces VOC emissions to zero

  • Ecologically friendly with a characteristic odour mainly used for USA style Oil Leathers

  • VOC free

Vie Hot Oil 210 Application: Vie Hot Oil 210 can be applied as it is or diluted with Vie Hot Oil Extender depending on the absorption rate of the crust leather. Method of application can be by roller coater or curtain coater. Vie Hot Oil 210 is not water miscible. Vie Hot Oil 210 is especially popular with Hot Waxes like Vie Hot Wax MCP and MCM to achieve very dark pull up effects without highlighting defects.

Example Applications:

  1. Applied alone on full grain or buffed pull-up leather 1000 p. Vie Hot Oil 210 1 – 2 x heated reverse roller coater (60°C), 150 – 250 g/m2

  2. Mixed with Vie Hot Oil Extender, full grain or buffed leather 500 p. Vie Hot Oil 210 500 p. Vie Hot Oil Extender 1 – 2 x curtain coater (60°C), 215 g/m2

  3. Mixed with other Vie Hot Oils for different feel and depth of pull-up intensity 500 p. Vie Hot Oil 210 : 500 p. Vie Hot Oil 213 or Vie Hot Oil SS230 1 – 2 x roller coater (60°C), 215 g/m2

  4. Mixed with Vie Hot Waxes for strong pull up effects and for different feel and depth of pull-up intensity 500 p. Vie Hot Oil 210 500 p. Vie Hot Wax MCP 1 – 2 x roller coater (80°C), 215 g/m2

Recommendation: Clean roller coater with Vie Hot Wax Wash which disperses Vie Hot Oils very well ! For Formulations where fish eyes have been experienced before, addition of 5 – 10% Vie Hot Oil Extender to the Hot Oil/Wax will normally eliminate this problem Spray or Roller Coat Undiluted Vie Hot Oil 210 on Full Grain or Corrected Grain Semi Veg type Leathers, Leave over-night, and Plate or Iron 100 – 120oC for Medium Strong Fashionable Pull up effects. Finish over with suitable PU/Acrylic/Wax finishes for a wide range of Fashionable Leather effects Will not Spue in cold weather

Vie Hot Oil 212

Solids content: 100%

PH value: n/a

Composition: Vie Hot Oil 212 is a VOC free Light Oil designed to be used alone or with Hot melt waxes for USA style Pull up Leathers.

Description: Vie Hot Oil 212 is a greenish-brown, solvent-free oil. When applied to corrected or full grain leathers prior to finishing, it provides an excellent pull-up with a medium to strong surface darkening after hot plating. This oil is exceptionally useful for upgrading leathers as it does not highlight defects.

The main characteristics are:

  • Extends Hot Oils and Waxes on roller coaters, can be used also for Light to Strong Oil Pull up effects

  • Reduces VOC emissions to zero

  • Ecologically friendly with a characteristic odour mainly used for USA style Oil Leathers

  • VOC free

Vie Hot Oil 212 Application: Vie Hot Oil 212 can be applied as it is or diluted with Vie Hot Oil Extender depending on the absorption rate of the crust leather. Method of application can be by roller coater or curtain coater. Vie Hot Oil 212 is not water miscible. Vie Hot Oil 212 is especially popular with Hot Waxes like Vie Hot Wax MCP and MCM to achieve very dark pull up effects without highlighting defects.

Example Applications:

  1. Applied alone on full grain or buffed pull-up leather 1000 p. Vie Hot Oil 212 1 – 2 x heated reverse roller coater (60°C), 150 – 250 g/m2

  2. Mixed with Vie Hot Oil Extender, full grain or buffed leather 500 p. Vie Hot Oil 212 500 p. Vie Hot Oil Extender 1 – 2 x curtain coater (60°C), 215 g/m2

  3. Mixed with other Vie Hot Oils for different feel and depth of pull-up intensity 500 p. Vie Hot Oil 212 : 500 p. Vie Hot Oil 210 or Vie Hot Oil SS230 1 – 2 x roller coater (60°C), 215 g/m2

  4. Mixed with Vie Hot Waxes for strong pull up effects and for different feel and depth of pull-up intensity 500 p. Vie Hot Oil 212 500 p. Vie Hot Wax MCP 1 – 2 x roller coater (80°C), 215 g/m2

Recommendation: Clean roller coater with Vie Hot Wax Wash which disperses Vie Hot Oils very well !

For Formulations where fish eyes have been experienced before, addition of 5 – 10% Vie Hot Oil Extender to the Hot Oil/Wax will normally eliminate this problem Spray or Roller Coat Undiluted Vie Hot Oil 212 on Full Grain or Corrected Grain Semi Veg type Leathers, Leave over-night, and Plate or Iron 100 – 120oC for Medium Strong Fashionable Pull up effects. Finish over with suitable PU/Acrylic/Wax finishes for a wide range of Fashionable Leather effects will not Spue in cold weather

Vie Hot Oil 213

Solids content: 100%

PH value: n/a

Composition: Vie Hot Oil 213 is a VOC free Dark Oil designed to be used alone or with Hot melt waxes for USA style Pull up Leathers.

Description: Vie Hot Oil 213 is a dark greenish-brown, solvent-free oil. When applied to corrected or full grain leathers prior to finishing, it provides an excellent pull-up with a medium strong to strong surface darkening after hot plating. This oil is exceptionally useful for upgrading leathers.

The main characteristics are:

  • Extends Hot Oils and Waxes on roller coaters, can be used also for Light to Strong Oil Pull up effects

  • Reduces VOC emissions to zero

  • Ecologically friendly with a characteristic odour mainly used for USA style Oil Leathers

  • Npe, Apeo, nmp free, VOC free

Vie Hot Oil 213 Application: Vie Hot Oil 213 can be applied as it is or diluted with Vie Hot Oil Extender depending on the absorption rate of the crust leather. Method of application can be by roller coater or curtain coater. Vie Hot Oil 213 is not water miscible. Vie Hot Oil 213 is especially popular with Hot Waxes like Vie Hot Wax MCB and MX to achieve very dark pull up effects without highlighting defects

Example Applications:

  1. Applied alone on full grain or buffed pull-up leather 1000 p. Vie Hot Oil 213 1 – 2 x heated reverse roller coater (60°C), 150 – 250 g/m2

  2. Mixed with Vie Hot Oil Extender, full grain or buffed leather 500 p. Vie Hot Oil 213 500 p. Vie Hot Oil Extender 1 – 2 x curtain coater (60°C), 215 g/m2

  3. Mixed with other Vie Hot Oils for different feel and depth of pull-up intensity 500 p. Vie Hot Oil 213 500 p. Vie Hot Oil 212 or Vie Hot Oil SS230 1 – 2 x roller coater (60°C), 215 g/m2

  4. Mixed with Vie Hot Waxes for strong pull up effects and for different feel and depth of pull-up intensity 500 p. Vie Hot Oil 213 500 p. Vie Hot Wax MCB 1 – 2 x roller coater (80°C), 215 g/m2

Recommendation: Clean roller coater with Vie Hot Wax Wash which disperses Vie Hot Oils very well ! For Formulations where fish eyes have been experienced before, addition of 5 – 10% Vie Hot Oil Extender to the Hot Oil/Wax will normally eliminate this problem Spray or Roller Coat Undiluted Vie Hot Oil 213 on Full Grain or Corrected Grain Semi Veg type Leathers, Leave over-night, and Plate or Iron 100 – 120oC for Strong Fashionable Pull up effects. Finish over with suitable PU/Acrylic/Wax finishes for a wide range of Fashionable Leather effects will not Spew in cold weather

Vie Hot Oil Extender Y

Solids content: 100%

PH value: n/a

Composition: Vie Hot Oil Extender Y is a VOC free Oil designed to aid the Finisher to reduce viscosity and reduce strength of Hot Oils and waxes without use of Toxic and flammable solvents. Can Also be used alone for Various Oil Pull up effects.

Description: Vie Hot Oil 213 is a dark greenish-brown, solvent-free oil. When applied to corrected or full grain leathers prior to finishing, it provides an excellent pull-up with a medium strong to strong surface darkening after hot plating. This oil is exceptionally useful for upgrading leathers.

The main characteristics are:

  • Extends Hot Oils and Waxes on roller coaters, can be used also for Light to Strong Oil Pull up effects

  • Reduces VOC emissions to zero

  • Ecologically friendly with a characteristic odour mainly used for USA style Oil Leathers

  • Npe, Apeo, nmp free, VOC free

Vie Hot Oil Extender Y Application: Extends and reduces viscosity off almost all types of Oils and Waxes used on Hot or Cold Roller coaters. Used Alone for Fashionable Elegant Pull up effects on Full and Corrected Grain Leathers.

Example Applications:

  • Melt Waxes or Oils and add in Vie Hot Oil Extender Y while hot and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  • For Formulations where fish eyes have been experienced before, addition of 5 – 10% Vie Hot Oil Extender Y to the Hot Oil/Wax will normally eliminate this problem.

  • Spray or Roller Coat Undiluted Vie Hot Oil Extender Y on Full Grain or Corrected Grain Semi Veg type Leathers, Leave over-night, and Plate or Iron 100 – 120oC for medium to Strong Fashionable Pull up effects. Finish over with suitable PU/Acrylic/Wax finishes for a wide range of Fashionable Leather effects

  • Will not Spew in cold weather

Vie Hot Oil Extender

Solids content: 100%

PH value: n/a

Composition: Vie Hot Oil Extender is a VOC free diluent designed to aid the Finisher to reduce viscosity and reduce strength of Hot Oils and waxes without use of Toxic and flammable solvents

The main characteristics are:

  • Extends Hot Oils and Waxes on roller coaters.

  • Reduces VOC emissions to zero

  • Ecologically friendly with a characteristic odour mainly used for USA style Oil Leathers

  • Npe, Apeo, nmp free, VOC free

Vie Hot Oil Extender Application: Extends and reduces viscosity off almost all types of Oils and Waxes used on Hot or Cold Roller coaters

Example Applications:: Melt Waxes or Oils and add in Vie Hot Oil Extender while hot and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc. For Formulations where fish eyes have been experienced before, addition of 10% to Hot Oil/Wax will eliminate this problem

Vie Hot Oil SS230

Solids content: 100%

PH value: n/a

Composition: Vie Hot Oil SS230 is a VOC free Oil designed to be used alone or with Hot Melt Waxes on USA style Leathers.

Description: Vie Hot Oil 213 is a dark greenish-brown, solvent-free oil. When applied to corrected or full grain leathers prior to finishing, it provides an excellent pull-up with a medium strong to strong surface darkening after hot plating. This oil is exceptionally useful for upgrading leathers.

The main characteristics are:

  • Used on Oily Nubucks and Suedes for a Waxy/Grabby/Oily feel that stays

  • Reduces VOC emissions to zero

  • Ecologically friendly with a characteristic odour mainly used for USA style Oil Leathers

  • NUsed with other Hot Waxes or Oils to achieve a strong Pull up effect with a Waxy/Grabby feel

Vie Hot Oil SS230 Application: Used with almost all types of Oils and Waxes used on Hot or Cold Roller coaters to improve feel

Example Applications:

  1. Melt Waxes and/or Oils and add in Vie Hot Oil SS230 while hot, stir and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  2. Oily Nubuck Mix Vie Hot Oil SS230 2:1 to 1:1 with Vie Hot Oil Extender, stir and pour or pump onto Roller coater, use 60-80oC heat if penetration needs to be improved

Vie Hot Oil SS331

Solids content: 100%

PH value: n/a

Composition: Vie Hot Oil SS331 is a special Oil designed to be used alone or with Hot Melt Waxes on USA style Leathers. Is designed to be spue and fungus resistant. Contains state of the art Green Chemistry TCMTB free anti fungicides and perfume to maintain fresh smelling products even after long storage.

The main characteristics are:

  • Used on Oily Nubucks and Suedes for a Waxy/Grabby/Oily feel that stays

  • Slow penetration when applied cold, fast penetration when applied hot (60-80oC)

  • Maintains Softness of Leather

  • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Waxy/Grabby feel

Vie Hot Oil SS331 Application: Used with almost all types of Oils and Waxes used on Hot or Cold Roller-coaters to improve feel

Example Applications:

  1. Melt Waxes and/or Oils and add in Vie Hot Oil SS331 while hot, stir and pour or pump onto Roller-coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  2. Oily Nubuck Mix Vie Hot Oil SS331 2:1 to 1:1 with Vie Hot Oil Extender, stir and pour or pump onto Roller coater, use 60-80oC heat if penetration needs to be improved

Vie Hot Oil WP

Solids content: 100%

PH value: n/a

Composition: Vie Hot Oil WP is a VOC free Oil designed to be used alone or with Hot Melt Waxes on USA style Leathers.

The main characteristics are:

  • Used on Oily Nubucks and Suedes for a Waxy/Oily feel that stays

  • Reduces VOC emissions to zero

  • Dramatically improves Maeser and Bally penetrometer Water resistance

  • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Waxy/Oily feel

Vie Hot Oil WP Application: Used with almost all types of Oils and Waxes used on Hot or Cold Roller coaters to improve feel

Example Applications:

  1. Melt Waxes and/or Oils and add in Vie Hot Oil WP while hot, stir and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  2. Oily Nubuck Mix Vie Hot Oil WP 2:1 to 1:1 with Vie Hot Oil Extender, stir and pour or pump onto Roller coater, use 60-80oC heat if penetration needs to be improved

Vie Hot Stuff PUW

Solids content: 100%

PH value: n/a

Composition: Vie Hot Stuff PUW is a VOC free Hot Wax designed to be used alone or with Hot Melt Oils on USA style Leathers. Vie Hot Stuff PUW is white by nature and can be even be used on Pastel colored Leathers. It results in a strong yet clean pull up effect and does not overly harden leathers.

The main characteristics are:

  • Used on USA style Leathers like Crazy Horse for strong Pull up effect

  • Reduces VOC emissions to zero

  • Ecologically friendly and virtually no odour

  • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Dry Natural feel

Vie Hot Stuff PUW Application: Used with almost all types of Oils and Waxes used on Hot Roller coaters to give a long lasting strong Pull up effect

Example Applications:

  1. Melt Hot Stuff PUW at about 80oC, and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  2. Can be used 2:1 to 1:1 with Vie Hot Oil Extender, for Lower strength Pull Up effects and more drain back, pour or pump onto Roller coater, use 70-80oC

  3. Can be used with Other Vie Oils like Vie Hot Oil SS230 if more waxy effect is required

  4. Can be used with Vie Hot Oil WP for Maeser or W/P Leathers

Vie Hot Stuff PUY

Solids content: 100%

PH value: n/a

Composition: Vie Hot Stuff PUY is a VOC free Hot Wax designed to be used alone or with Hot Melt Oils on USA style Leathers. It results in a strong pull up effect and does not overly harden leathers.

The main characteristics are:

  • Used on USA style Leathers like Crazy Horse for strong Pull up effect

  • Reduces VOC emissions to zero

  • Ecologically friendly and virtually no odour

  • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Dry Natural feel

Vie Hot Stuff PUY Application: Used with almost all types of Oils and Waxes used on Hot Roller coaters to give a long lasting strong Pull up effect

Example Applications:

  1. Melt Hot Stuff PUY at about 80oC, and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  2. Can be used 2:1 to 1:1 with Vie Hot Oil Extender, for Lower strength Pull Up effects and more drain back, pour or pump onto Roller coater, use 70-80oC

  3. Can be used with Other Vie Oils like Vie Hot Oil SS230 if more waxy effect is required

  4. Can be used with Vie Hot Oil WP for Maeser or W/P Leathers

Vie Hot Stuff UAP

Solids content: 100%

PH value: n/a

Composition: Vie Hot Stuff UAP is a VOC free Hot Wax designed to be used alone or with Hot Melt Oils on USA style Leathers.

The main characteristics are:

  • Used on USA style Leathers like Crazy Horse for strong Pull up effect

  • Reduces VOC emissions to zero

  • Ecologically friendly and virtually no odour, no tendency to spew in cold weather

  • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Dry Natural feel

Vie Hot Stuff UAP Application: Used with almost all types of Oils and Waxes used on Hot Roller coaters to give a long lasting strong Pull up effect

Example Applications:

  1. Melt Hot Stuff UAP at about 80oC, and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  2. Can be used 2:1 to 1:1 with Vie Hot Oil Extender, for Lower strength Pull Up effects and more drain back, pour or pump onto Roller coater, use 70-80oC

  3. Can be used with Other Vie Oils like Vie Hot Oil SS230 if more waxy effect is required.

  4. Can be used with Vie Hot Oil WP for Maeser or W/P Leathers

Vie Hot Stuff WG

Solids content: 100%

PH value: n/a

Composition: Vie Hot Stuff WG is a VOC free Hot Wax designed to be used alone or with Hot Melt Oils on USA style Leathers.

The main characteristics are:

  • Used on USA style Leathers like Crazy Horse for strong Pull up effect

  • Reduces VOC emissions to zero, ecologically friendly

  • Used in Wax “Wash back system”

  • Used alone to achieve a strong Pull up effect with a warm waxy natural feel

Vie Hot Stuff WG Application: Used with almost all types of Oils and Waxes used on Hot Roller coaters to give a long lasting strong Pull up effect

Example Applications:

  1. Melt Hot Stuff WG at about 80oC, and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  2. Can be used 2:1 to 1:1 with Vie Hot Oil Extender, for Lower strength Pull Up effects and more drain back, pour or pump onto Roller coater, use 70-80oC

  3. Can be used in “wax wash back system” apply by pad or roller, leave overnight, put back in drum and wash with either just water or water with pH adjusted to 4 with formic acid and run as required, run 10-20 minutes, dry and continue process with heated tumble drier etc

  4. Can be used alone or with Vie Hot Oil WP for Maeser or W/P Leathers

Vie Hot Wax DX

Solids content: 100%

PH value: n/a

Composition: Vie Hot Wax DX is a VOC free Hot Wax designed to be used alone or with Hot Melt Oils on USA style Leathers.

The main characteristics are:

  • Used on USA style Leathers like Crazy Horse for strong Pull up effect

  • Reduces VOC emissions to zero

  • Ecologically friendly and virtually no odour, no tendency to spew in cold weather

  • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Dry Natural feel

Vie Hot Wax DX Application: Used with almost all types of Oils and Waxes used on Hot Roller coaters to give a long lasting strong Pull up effect

Example Applications:

  • Melt Hot Wax DX at about 70oC, and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  • Can be used 2:1 to 1:1 with Vie Hot Oil Extender, for Lower strength Pull Up effects and more drain back, pour or pump onto Roller coater, use 70-80oC

  • Can be used with Other Vie Oils like Vie Hot Oil SS230 if more waxy effect is required

  • Can be used with Vie Hot Oil WP for Maeser or W/P Leathers

Vie Hot Wax MCB

Solids content: 100%

PH value: n/a

Composition: Vie Hot Wax MCB is a VOC free Dark Hot Wax designed to be used alone or with Hot Melt Oils on USA style Leathers

The main characteristics are:

  • Used on USA style Leathers like Crazy Horse for strong Pull up effect

  • Reduces VOC emissions to zero

  • Ecologically friendly and virtually no odour, no tendency to spew in cold weather

  • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Soft Waxy Natural feel

Vie Hot Wax MCB Application: Used with almost all types of Oils and Waxes used on Hot Roller coaters to give a long lasting strong Pull up effect

Example Applications:

  • Melt Hot Wax MCB at about 70oC, and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  • Can be used 2:1 to 1:1 with Vie Hot Oil Extender, for Lower strength Pull Up effects and more drain back, pour or pump onto Roller coater, use 70-80oC

  • Can be used with Other Vie Oils like Vie Hot Oil SS230 if more waxy effect is required

  • Can be used with Vie Hot Oil WP for Maeser or W/P Leathers

Vie Hot Wax MCM

Solids content: 100%

PH value: n/a

Composition: Vie Hot Wax MCM is a VOC free Hot Wax designed to be used alone or with Hot Melt Oils on USA style Leathers

The main characteristics are:

  • Used on USA style Leathers like Crazy Horse for a dark strong Pull up effect

  • Reduces VOC emissions to zero

  • Ecologically friendly and virtually no odour

  • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a dry Waxy Natural feel

  • Combinations of Wax raw materials makes color matching easy, no greenish, no reddish tones

Vie Hot Wax MCM Application: Used with almost all types of Oils and Waxes used on Hot roller-coaters to give a long lasting dark strong Pull up effect

Example Applications:

  1. Melt Hot Wax MCM at about 80oC, and pour or pump onto roller-coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  2. Can be used 2:1 to 1:1 with Vie Hot Oil Extender, for Lower strength Pull Up effects and more drain back, pour or pump onto roller-coater, use 80oC

  3. Can be used with Other Vie Oils like Vie Hot Oil SS230 if more waxy effect is required

  4. Can be used with Vie Hot Oil WP for Maeser or W/P Leathers

Vie Hot Wax MCP

Solids content: 100%

PH value: n/a

Composition: Vie Hot Wax MCP is a VOC free Hot Wax designed to be used alone or with Hot Melt Oils on USA style Leathers.

The main characteristics are:

  • Used on USA style Leathers like Crazy Horse for a medium strong clean Pull up

  • Reduces VOC emissions to zero

  • Ecologically friendly and virtually no odour

  • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Soft Waxy Natural feel

  • Combinations of Wax raw materials makes color matching easy, no greenish, no reddish tones

Vie Hot Wax MCP Application: Used with almost all types of Oils and Waxes used on Hot roller-coaters to give a long lasting medium strong Pull up effect

Example Applications:

  1. Melt Hot Stuff PUY at about 80oC, and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  2. Can be used 2:1 to 1:1 with Vie Hot Oil Extender, for Lower strength Pull Up effects and more drain back, pour or pump onto Roller coater, use 70-80oC

  3. Can be used with Other Vie Oils like Vie Hot Oil SS230 if more waxy effect is required

  4. Can be used with Vie Hot Oil WP for Maeser or W/P Leathers

Vie Hot Wax MX

Solids content: 100%

PH value: n/a

Composition: Vie Hot Wax MX is a VOC free Hot Wax designed to be used alone or with Hot Melt Oils on USA style Leathers

The main characteristics are:

  • Used on USA style Leathers like Crazy Horse for a medium strong Pull up effect

  • Reduces VOC emissions to zero

  • Ecologically friendly and virtually no odour, no tendency to spew in cold weather

  • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Soft Waxy Natural feel

Vie Hot Wax MX PUY Application: Used with almost all types of Oils and Waxes used on Hot Roller coaters to give a long lasting medium strong Pull up effect

Example Applications:

  • Melt Hot Stuff PUY at about 80oC, and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

  • Can be used 2:1 to 1:1 with Vie Hot Oil Extender, for Lower strength Pull Up effects and more drain back, pour or pump onto Roller coater, use 70-80oC

  • Can be used with Other Vie Oils like Vie Hot Oil SS230 if more waxy effect is required

  • Can be used with Vie Hot Oil WP for Maeser or W/P Leathers

  • Vie Hot Wax Wash

    Solids content: tba

    PH value: tba

    Composition: Vie Hot Wax Wash is a special non ionic emulsifier designed to aid the Finisher to wash off Roller coaters after application of Hot Oils and waxes without use of Toxic and flammable solvents

    The main characteristics are:

    • Quickly and easily emulsifies Oils and Waxes on roller coaters and spraying machines

    • Reduces VOC emissions to zero

    • Ecologically friendly and highly efficient in washing off Equipment used for USA style Oil Leathers

    • Npe, Apeo, nmp free, VOC free

    Vie Hot Wax Wash Application: Emulsifies almost all types of Oils and Waxes used on Hot or Cold Roller coaters

    Example Applications:

    Pour onto roller coater while still hot, run for around 10 minutes, slowly add Warm Water and run around 5 minutes, run washer tap and drain. A second application may be used if machine is to be used cold for Pigment application to ensure no fish eyes or cratering

    Vie Magic Wax A

    Solids content: 100%

    PH value: n/a

    Composition: Vie Magic Wax A is a VOC free Hot Wax designed to be used alone or with Hot Melt Oils on USA style Leathers, specially refined, bleached and purified and pulverized to a fine flour like powder for pepper pot fashion looks

    The main characteristics are:

    • Used on USA style Leathers like Crazy Horse for strong Pull up effect

    • Reduces VOC emissions to zero

    • Ecologically friendly and virtually no odour, no tendency to spew in cold weather

    • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Dry Natural feel

    • Used alone by pepper pot application for wild and wonderful fashion effects only limited by your imagination

    Vie Magic Wax A Application: Used with almost all types of Oils and Waxes used on Hot Roller coaters to give a long lasting strong Pull up effect, used alone with Pepper pot application for all sorts of waxed patterned fashion effects, polishes to an extreme clear high gloss

    Example Applications:

    • Melt Magic Wax A at about 100oC, and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

    • Can be used 2:1 to 1:1 with Vie Hot Oil Extender, for Lower strength Pull Up effects and more drain back, pour or pump onto Roller coater, use 90-100oC

    • Can be used with Other Vie Oils like Vie Hot Oil SS230 if more waxy effect is required

    • Can be used with Vie Hot Oil WP for Maeser or W/P Leathers

    • Used alone by pepper pot application for many types of waxed fashion effects

    Vie Oil PW

    Solids content: 60%

    Composition: Vie Oil T is an aqueous emulsion of vegetable and synthetic oils.

    Description: Vie Oil PW is a milky, white liquid of medium viscosity, which is dilutable with water. The product is specially developed for glazed, polish, resin and pull-up-finishes. Vie Oil PW shows following properties

    The main characteristics are:

    • Softening additive for Proteins, and Waxes such as Vie Antik Waxes

    • For Polished finishes as a pre-ground to even out absorbency of the crust

    • To improve repolishability

    • Medium to strong Pull up effect, when applied heavily without dilution

    Vie Oil PW Application:Vie Oil PW is used alone or in combination with suitable protein binders in polish or pre-grounds on full grain or buffed leathers. The product improves considerably inferior leathers (Upgrading). Vie Oil PW evens out the absorbency of the crusts and keeps a fine grain break. For pull-up articles, Vie Oil PW is applied undiluted on the crust usually by roller coater, it can also be used in conjunction with Vie Antik Wax 30 or 40 for Fashionable Waxed Pull up effects.

    Example Applications:

    • Polish ground for Imitation Glazed Leathers

    • 50 parts Vie Super penetrator

    • 625 parts Water

    • 100 parts Vie Wax Top C

    • 75 parts Vie Oil PW

    • 50 parts Viepur Micro

    • 100 parts Vie Lustre SS

    • spray 1 x, polish on a felt

    Base coat

    • 450 parts Water

    • 25 parts Vie Super penetrator

    • 100 parts Vie Lustre H

    • 50 parts Viecryl TG36

    • 50 parts Viecryl XL97

    • 50 parts Vie Top 137

    • 50 parts Viepur Flow

    • 25 parts Vietint Ultrafine pigments

    • spray x 2 – 3 light

    Top coat

    • 500 parts Viepur Top FL-01

    • 435 parts Water

    • 50 parts Vie Lustre H

    • 10 parts Vlelink AZ

    • 5 parts Viefeel DW

    • spray x 1 – 2 , Iron or Kiss plate 100 – 120° C

    Vie Oil T

    Solids content: 70% (tba)

    Composition: Vie Oil T is an aqueous emulsion of vegetable and synthetic oils.

    Description: Vie Oil T is a milky, white liquid of medium viscosity, which is dilutable with water. The product is specially developed for glazed, polish, resin and pull-up-finishes. Vie Oil T shows following properties

    The main characteristics are:

    • Used on USA style Leathers like Crazy Horse for a dark strong Pull up effect

    • Softening additive for Proteins

    • For Polished finishes as a preground to even out absorbency of the crust

    • To improve re-polishability

    • Medium to strong Pull up effect, when applied heavily without dilution

    Vie Oil T Application: Vie Oil T is used alone or in combination with suitable protein binders in polish or pregrounds on full grain or buffed leathers. The product improves considerably inferior leathers (Upgrading). Vie Oil T evens out the absorbency of the crusts and keeps a fine grain break. For pull-up articles, Vie Oil T is applied undiluted on the crust usually by roller coater.

    Example Applications:

    Polish ground for Imitation Glazed Leathers

    • 50 parts Vie Super penetrator

    • 625 parts Water

    • 100 parts Vie wax top C

    • 75 parts Vie Oil T

    • 50 parts Viepur Micro

    • 100 parts Vie Lustre SS

    • spray 1 x, polish on a felt

    Base coat

    • 450 parts Water

    • 25 parts Vie Super penetrator

    • 100 parts Vie Lustre H

    • 50 parts Viecryl TG36

    • 50 parts Viecryl XL97

    • 50 parts Vie Top 137

    • 50 parts Viepur Flow

    • 25 parts Vietint Ultrafine pigments

    • spray x 2 – 3 light

    Top coat

    • 500 parts Viepur Top Elegante

    • 435 parts Water

    • 50 parts Vie Top 137

    • 10 parts Vlelink AZ

    • 5 parts Viefeel DW

    • spray x 1 – 2 , Iron or Kiss plate 100 – 120° C

    Vie Prima Dark Oil 88

    Solids content: 95%

    PH value: n/a

    Composition: Vie Prima Dark Oil 88 is a Special Compact Oil designed to be used alone or with Hot Melt Waxes on USA style Leathers

    The main characteristics are:

    • Used on Oily Nubucks and Suedes for a Waxy/Grabby/Oily feel that stays

    • Easy to use, strong, long lasting, Waxy Silky Feel

    • Biodegradable and contains added Perfume for a pleasant aroma

    • Used with other Hot Waxes or Oils to achieve a strong Pull up effect with a Waxy/Grabby feel

    Vie Prima Dark Oil 88 Application: Used with almost all types of Oils and Waxes used on Hot or Cold Roller coaters to improve feel

    Example Applications:

    1. Melt Waxes and/or Oils and add in Vie Prima Dark Oil 88 while hot, stir and pour or pump onto Roller coater blades, allow 5 – 10 minutes for temperature of blade to stabilize before running production to ensure no fish eyes etc.

    2. Oily Nubuck Mix Vie Prima Dark Oil 88 2:1 to 1:1 with Vie Hot Oil Extender, stir and pour or pump onto Roller coater, use 60-80oC heat if penetration needs to be improved

    3. BBG (Base Ball Glove) use Vie Prima Dark Oil 88 without dilution or with Vie Hot Oil Extender as required on hot roller coater at 60-70oC x 1 to x 2 passes as requireds

    Vie Wax PV260

    Solids content: 100%

    PH value: n/a

    Composition: Vie Wax PV260 is an aqueous emulsion of an Alkene Polymer.

    Description: Vie Wax PV260 is a white liquid of medium viscosity, which is dilutable with water. The product is specially developed for Scrunched, Fashion pull-up-finishes. Vie Wax PV260 shows following properties

    The main characteristics are:

    • Used alone directly onto crust

    • Not actually a wax but a synthetic polymer so does not increase oil content in leather

    • Shows good adhesion to adhesives, soles etc

    • Medium to strong Pull up effect, when applied heavily without dilution and Hot Plated or ironed

    Vie Wax PV260 Application: Vie Wax PV260 is normally used alone on full grain or buffed leathers. The product improves considerably inferior leathers (Upgrading). Vie Wax PV260 evens out the absorbency of the crusts and keeps a fine grain break. For pull-up articles, Vie Wax PV260 is applied undiluted on the crust usually by roller coater,

    Example Applications:

    • Crazy Horse type Pull Up Leathers - Apply 8-15 grams per square foot by Spray, Pad or Roller coat etc. Leave a few hours or overnight. Plate or Iron 100oC plus Short Dry Mill for effect.

    • Glossy Scrunched effect Handbag - Apply 12 grams per square foot by spray, Pad or Roller coat etc. Leave a few hours. Polish Felt. Iron 120oC 30 Bar 3 m/m

    • Adhesion coat spray x 1

    • Water 250 grams

    • Vie Super Penetrator LC 50 parts

    • Viepur Micro or Viepur 89 150 parts

    • Viepur-35 50 parts

    • Base coat spray x 2 Plate/Iron 90oC spray x 1-2

    • Water 300 parts

    • Viecryl-7 150 parts

    • Viecryl 94 100 parts

    • Vie Lustre SS 50 parts

    • Vie Lustre H 75 parts

    • Viepur-35 75 parts

    • Viesol LD dye as required

    • Vie Wax 816 50 parts

    • Top Coat spray x 1 – 2 Plate/Iron 110oC

    • Water 488 parts

    • Vielink AZ 2 parts

    • Viepur Top GP 400 parts

    • Vie Top 137 100 parts

    • Vie Feel RL 10 parts

    • Stake and Mill as required

    Viematt 38

    Solids content: 20%

    PH value: 8+-

    Composition: Viematt 38 is a soft non ionic aqueous fine particle Silica Based Filler/Duller dispersed in a non ionic synthetic wax..

    The main characteristics are:

    • retains a fine grain and break

    • has a high matting effect with excellent light and heat fastness

    • improves feel and surface levelness and coverage

    • reduces tackiness, improves plating and stacking properties

    Vie Wax PV260 Application:
    Use on all types of Leather in the base coat to reduce tack and gloss, and improve plateability and stackability. Due to its characteristics it is especially suitable for matting high-quality base coats, e. g. car upholstery. In general Viematt 38 is also a suitable component in conventional upholstery and shoe upper leather base coats.

    Viematt 38 may also be used to Dull Aqueous Top coats for general purpose Leathers, it can be used in both anionic and cationic finishes

    Example Applications: Add 25 – 100 parts per kg of base coat mix as required for all types of Leathers. Due to its Thixotropic nature stir well before use.

    Vie Wax 5050

    Solids content: 7 – 8%

    PH value: 8+-0.5

    Composition: Vie Wax 5050 is an aqueous Synthetic Wax emulsion for all types of Leathers

    The main characteristics are:

    • Reduces Tack and Improves Plate release in Base and Top coats

    • Gives a pleasant Waxy silky feel to the Finish

    • Has good heat and light fastness

    • Can be used also as an over-spray on finished Leathers to improve feel

    Vie Wax 5050 Application: Used on all types of Leathers mainly in the Base coat to give a waxy feel and improve plate release

    Example Applications:

    • Add 25 – 100 parts per kg in aqueous Base Coats for all types of Leathers to improve plate release and softness

    • Use as an over-spray Feel coat 100 – 250 parts Vie Wax 5050 with 200 – 750 parts Water for a waxy feel or can also add 2 – 5 parts Vie Feel 251 or Vie Feel 760 for a more silky sensuous feel, spray light or as required, can be followed by a light Iron or Hot Plate 80oC +

    Vie Wax 505

    Solids content: 7 – 8%

    PH value: 8+-0.5

    Composition: Vie Wax 505 is an aqueous Synthetic Wax emulsion for all types of Leathers

    The main characteristics are:

    • Reduces Tack and Improves Plate release in Base and Top coats

    • Gives a pleasant Waxy silky feel to the Finish

    • Has good heat and light fastness

    • Can be used also as an over-spray on finished Leathers to improve feel

    Vie Wax 505 Application: Used on all types of Leathers mainly in the Base coat to give a waxy feel and improve plate release

    Example Applications:

    • Add 25 – 100 parts per kg in aqueous Base Coats for all types of Leathers to improve plate release and softness

    • Use as an over-spray Feel coat 100 – 250 parts Vie Wax 505 with 200 – 750 parts Water for a waxy feel or can also add 2 – 5 parts Vie Feel 251 or Vie Feel 760 for a more silky sensuous feel, spray light or as required, can be followed by a light Iron or Hot Plate 80oC +

    Vie Catwax 86 - Cationic Wax

    The main characteristics are:

    • Good heat and light fastness

    • Deals off rough and damaged grain aiding upgrading as well as for snuffed or corrected leathers for a full grain look with a fine grain break

    • As a Top spray provides an attractive, silky feel and luster

    • Has an anti-static effect, reducing possible electric shocks during mechanical operations

    Vie Cat Wax 86 Application: Vie Cat Wax 86 is either used as Ground Coat in Finishing to upgrade and Seal off damaged grain or as a Top Spray after finishing to improve Naturalness and to Give an Unfinished sensual feel to the Leather.

    • Appearance: creamy white liquid/paste

    • Chemical character: fatty acid condensation product

    • Ionic character: mildly cationic

    • Active substance: circa 12.5% +-1%

    • pH value: approx. 3 – 5

    • Compatibility: good with cationic, amphoteric and nonionic products, can be used with anionic products in small quantities if diluted before addition.

    • Storage stability: minimum 1 year under cool and dry conditions when stored in original,sealed packaging.

    Example Applications:

    All types of Soft Leathers for Ground coat:

    Water 300 – 500 parts
    Vie Cat Wax 86 25 – 100 parts
    Viepur Catbase 200 – 300 parts
    Vie Microtint Pigments 0 – 50 parts

    Spray or Roller x 1 wet, dry well and Hot Iron or Plate low pressure some dwell, finish as usual

    High Performance Shoe Leathers, Sofa Leathers etc Ground coat:

    Water 300 – 500 parts
    Viepur Cat HP 50 – 100 parts
    Vie Catbase 200 – 400 parts
    Vie Cat Wax 86 25 – 50 parts
    Vie Microtint Pigments 0 – 50 parts

    Spray or Roller x 1 wet, dry well and Hot Iron or Plate low pressure some dwell, finish as usual

    Anionic finishes: 25 to 50 parts dilute well add into total 1 kg base coat mix, check compatibility

    Vie Cat Wax 19 – Cationic Wax

    Solids content: 100%

    PH value: n/a

    Application: Vie Cat Wax 19 is either used as Ground Coat in Finishing to upgrade and Seal off damaged grain or as a Top Spray after finishing to improve Naturalness and to Give an Unfinished sensual feel to the Leather

    The main characteristics are:

    • Good heat and light fastness

    • Deals off rough and damaged grain aiding upgrading as well as for snuffed or corrected leathers for a full grain look with a fine grain break

    • As a Top spray provides an attractive, silky feel and luster

    • Has an anti-static effect, reducing possible electric shocks during mechanical operations

    Vie Cat Wax 19 Application: Vie Cat Wax 19 is diluted with cold water as required and sprayed or roller coated onto the crust. Can be used in combination with Viepur Cat HP or with Vie Catbase in any proportion, may be colored with non ionic Vie Microtint Pigments for maximum coverage. Hot Ironing or Plating helps to seal off damaged and rough grain giving a dramatic upgrading of Leathers without hardening

    Example Applications:

    • Appearance: creamy white liquid/paste

    • Chemical character: fatty acid condensation product

    • Ionic character: mildly cationic

    • Active substance: circa 12 % +-1%

    • pH value: approx. 3 – 5

    • Compatibility: good with cationic, amphoteric and nonionic products, can be used with anionic products in small quantities if diluted before addition.

    • Storage stability: minimum 1 year under cool and dry conditions when stored in original, sealed packaging.

    Vie Wax 60

    Solids content: 20%

    PH value: tba

    Composition: Vie Wax 60 is a Soft Natural Carnauba Wax emulsion made especially to dry with a whitish appearance which melts into the crust by hot plating or polishing leaving a well filled fine grain with high gloss and optimum color development especially desirable in dark shades like Black . It may be used alone directly onto the crust, dilute as required, penetration may be increased with penetrator or IPA etc.

    The main characteristics are:

    • Initially gives a whitish look but polishes/plates to a clear high gloss

    • Gives a pleasant Waxy silky feel to the Finish

    • Has good heat and light fastness

    • Can be used with other oils and waxes for a wide range of polishable, burnishable aniline leathers

    • Biodegradable natural product

    Vie Wax 60 Application: Used as a primer for fashionable handbag leathers, spray, pad or roller Vie Wax 60, dry well and either polish plate or iron or a combination of these to develop colours and gloss and prepare crust for further finishing. The final milling pattern is prepared with the amount of Vie Wax 60 absorbed into the crust.

    Example Applications:

    • Spray Handbag Primer: Water 100 parts Vie Super Penetrator LC 50 parts Vie Wax 60 350 parts, dry well, polish felt, iron 110oC 20 bar, stake and short mill

    • Spray x 1 -2 base coat: Water 200 parts Vie Super Penetrator LC 25 parts Viecryl 7 100 parts Viecryl 61 300 parts Vie Lustre SS 50 parts Vie Lustre H 50 parts Vie Wax 60 100 parts Vie Microtint Black/Jet Black 75 parts Viesol LD Black W 25 parts.

    • Spray x 1 -2 Polishable Top coat: Vielac W-88 200 parts Water 100 parts Viesol LD Black W 2 parts Vie Feel SS 2-10 parts. Plate Stake Butterfly Mill etc to required effect

    Vie Antik Wax 30

    Solids content: tba

    PH value: tba

    Composition: Vie Antik Wax 30 is a fine particle natural Carnauba Wax emulsion for all types of Fashion Leathers

    The main characteristics are:

    • Use alone, or with penetrator etc for Burnish Leathers

    • Gives a pleasant Waxy Natural feel to the Finish

    • Has good darkening in the Shoe room with carnauba wax bars and wool mop

    • Can be used also with Protein binders for various Fashion effects

    Vie Antik Wax 30 Application: Used on all types of Fashion Leathers mainly alone or with penetrators as first spray coat or in the Base coat to give a Waxy Feel and improve darkening in the shoe room

    Example Applications:

    • Use alone or with Water and Vie Super penetrator as first coat for Semi Veg Burnish Leathers

    • Use with Vie Lustre H and Vie Lustre SS for Glossy Burnish Leathers, can be followed by a light Iron or Hot Plate 90 – 110oC

    Vie Antik Wax 40

    Solids content: 21% +-1

    PH value: 7-8

    Composition: Vie Antik Wax 40 is a fine particle natural Carnauba Wax emulsion for all types of Fashion Leathers.

    The main characteristics are:

    • Use alone, or with penetrator etc for Burnish Leathers

    • Gives a pleasant Waxy Natural feel to the Finish

    • Has good darkening in the Shoe room with carnauba wax bars and wool mop

    • Can be used also with Protein binders for various Fashion effects

    Vie Antik Wax 40 Application: Used on all types of Fashion Leathers mainly alone or with penetrators as first spray coat or in the Base coat to give a Waxy Feel and improve darkening in the shoe room

    Example Applications:

    • Use alone or with Water and Vie Super penetrator as first coat for Semi Veg Burnish Leathers

    • Use with Vie Lustre H and Vie Lustre SS for Glossy Burnish Leathers, can be followed by a light Iron or Hot Plate 90 – 110oC

    Vie Antik Wax 50

    Solids content: tba

    PH value: tba

    Composition: Vie Antik Wax 50 is a fine particle natural Rice Bran Wax emulsion for all types of Fashion Leathers

    The main characteristics are:

    • Use alone, or with penetrator etc for Burnish Leathers

    • Gives a pleasant Waxy Natural feel to the Finish

    • Has good darkening in the Shoe room with carnauba wax bars and wool mop

    • Can be used also with Protein binders for various Fashion effects

    Vie Antik Wax 50 Application: Used on all types of Fashion Leathers mainly alone or with penetrators as first spray coat or in the Base coat to give a Waxy Feel and improve darkening in the shoe room

    Example Applications:

    • Use alone or with Water and Vie Super penetrator as first coat for Semi Veg Burnish Leathers

    • Use with Vie Lustre H and Vie Lustre SS for Glossy Burnish Leathers, can be followed by a light Iron or Hot Plate 90 – 110oC

    Vie Antik Wax 80

    Solids content: tba

    PH value: tba

    Composition: Vie Antik Wax 80 is a fine particle natural Dark Hard Carnauba Wax emulsion for all types of Fashion Leathers, provides leather with a high degree of darkening and shine.

    The main characteristics are:

    • Use alone, or with penetrator etc for Burnish Leathers

    • Gives a pleasant Dry Waxy Natural feel to the Finish

    • Has good darkening in the Shoe room with carnauba wax bars and wool mop

    • Can be used also with Protein binders for various Fashion effects

    • Has a very high and long lasting gloss when polished with carnauba or ironed hot

    Vie Antik Wax 80 Application: Used on all types of Fashion Leathers mainly alone or with penetrators as first spray coat or in the Base coat to give a Waxy Feel and improve darkening in the shoe room.

    Example Applications:

    • Use alone or with Water and Vie Super penetrator as first coat for Semi Veg Burnish Leathers

    • Use with Vie Lustre H and Vie Lustre SS for Glossy Burnish Leathers, can be followed by a light Iron or Hot Plate 90 – 110oC

    Vie Bag Wax

    Solids content: 20%

    PH value: tba

    Composition: Vie Bag Wax is a silica free micronized organic matt polymer homogenized into PE waxes and bound with polishable micro fine aliphatic Polyurethanes and modified with, flow agents etc. Vie Bag Wax has no limit in its ability to help the finisher make a wide range of “Fantasy” Fashion effects only limited by their imagination. Vie Designer Wax has special micronized polymers with a wide range of molecular sizes which give remarkable upgradation at the same time providing the leather with a lush silky soft handle and a natural grain break, keeping Leather as natural as possible. It may be used alone directly onto the crust, or used with Viesol LD dyes on crust or base coated leathers for various two tone antique or marble effects, or add 1-2% Vie Microtint White pigment and make your own White Wax for pigmented pull up or waxed effects.

    The main characteristics are:

    • Covers and fills defects, gives whitish look with high polishability

    • Gives a pleasant Waxy silky feel to the Finish

    • Has good heat and light fastness

    • Can be used as a White wax for fantasy pigmented leathers or with other oils and waxes for a wide range of polishable, burnishable aniline leathers

    • Add to Top coats for Matt, Silk like feeling Leathers, use as complete base to top for Velour and Nubuck type leathers

    Vie Bag Wax Application: Used on all types of Leathers for a wide range of Fashionable Fantasy finishes. Vie Bag Wax is preferably used for high gloss polishing effects on smooth leathers and embossed leathers; it leads to a glossy two tone effect on the tips of the grain. When rotoplating at 110 –120° C the gloss of the leather is increased considerably. By adding Vie Bag Wax to Oils like Vie Oil PW and Waxes like Vie Antik Wax 40 a wide range of controlled white break effects and aged second hand looks can be developed. Use directly onto crust with or without Viesol LD dyes or Vie Microtint pigments for Velour/Nubuck looking and feeling leathers, apply in circular motions by pad, brush or sponge for Marble designs etc.

    Example Applications:

    • Add 50 – 150 parts per kg with Vie Oil PW and Vie Antik Wax 40 for increased whitening effect

    • Use as an over-spray Feel coat 100 – 250 parts Vie Bag Wax with 200 – 750 parts Water for a waxy sensuous feel, spray light or as required, can be followed by a light Iron or Hot Plate 100oC + Dry Mill for whitish look.

    • Use over pigmented base coats for Fashionable White break look, best results with x 1 – 2 sprays 200 parts Viepur-35 50 parts Vie Microtint pigments and 750 parts water followed by two sprays Vie Designer Wax 500 parts Vie Microtint White pigment 5 – 10 parts Water 475 parts 15-25 parts Viesol LD dyes, and Top coat Vielac W-88 200 parts Water 100 parts Vie Feel SS 2-10 parts. Plate Stake Mill etc to required effect.

    Vie Canvas Wax

    Solids content: 30%

    PH value: 10+-1

    Composition: Vie Canvas Wax is a high solids emulsifier free highly bleached top grade Paraffin Wax emulsion. Vie Canvas Wax has been saponified to create Stearates in-situ which provides water repellency to cloths and canvas . It may be used alone directly onto the cloth, or used with small amounts of either Viesol LD dyes or Vie Microtint pigments for various two tone antique or marble effects, or add 1-2% Vie Microtint White pigment and make your own White Wax for waxed pull up or vintage waxed effects. Vie Canvas Wax has no limit in its ability to help the Designer create a wide range of “Fantasy” Fashion effects only limited by their imagination. Apply by Dip, Roller, Pad or Spray. Dry well. Apply 2nd Coat if more vintage look is required (with addition of 1-2% Vie Microtint White) or Apply Vie Designer Wax lightly with or without color.

    The main characteristics are:

    • Stiffens Cloths, Adds Stand to materials, adds character to lifeless articles

    • Gives a pleasant Waxy silky feel to the Cloth

    • Has good heat and light fastness

    • Can be used as a White wax by addition of 1-2% Vie Microtint White

    • Provides static water-repellency

    Vie Wax 60 Application: Used on all types of Cloths for a wide range of Fashionable Fantasy finishes. Vie Canvas Wax is preferably used for adding character, handle and water repellency to dull lifeless cloths. When Ironing at 110 –120° C the gloss of the finish is increased considerably as well as achieving a darkening effect. By formulating with Vie Designer Wax, Oils like Vie Oil PW and harder darker waxes like Vie Antik Wax 40 a wide range of controlled white break effects and aged second hand looks can be developed., apply in circular motions by pad, brush or sponge for Marble designs etc.

    Example Applications:

    • Use un-diluted as Dipping solution for Canvas and Cloths, Dry well with heat, iron 120-140oC, Tumble for broken vintage effect

    • Use with Vie Penetrator LC, Water for Pad or Spray onto Cloth, Jute, etc to add character and stand in cloths for Handbags etc.

    • Use for “Magma Climax” fashion effect for handbags, apply in following method: 1/ Pad wet Vie Canvas Wax onto old low quality even crack grained leathers, dry hot if possible at 100oC, stake and mill to crack grain, spray x 2-3 wet Viepur-35, Spray x 1 Vielac W-88 diluted 2:1 with methoxy propanol, Iron 120oC mill, stake and butterfly, Kiss plate or light iron 120oC

    Vie Cat Wax -Cationic Wax

    Solids content: 20%

    PH value: tba

    Application: Vie Cat Wax is either used as Ground Coat in Finishing to upgrade and Seal off damaged grain or as a Top Spray after finishing to improve Naturalness and to Give an Unfinished sensual feel to the Leather…

    The main characteristics are:

    • Good heat and light fastness

    • Deals off rough and damaged grain aiding upgrading as well as for snuffed or corrected leathers for a full grain look with a fine grain break

    • As a Top spray provides an attractive, silky feel and luster

    • Has an anti-static effect, reducing possible electric shocks during mechanical operations

    Properties:

    • Appearance: creamy white liquid/paste

    • Chemical character: fatty acid condensation product

    • Ionic character: mildly cationic

    • Active substance: circa 14% +-1%

    • pH value: approx. 4 – 5

    • Compatibility: good with cationic, amphoteric and nonionic products.

    • Storage stability: minimum 1 year under cool and dry conditions when stored in original, sealed packaging.

    Vie Cat Wax Application: Vie Cat Wax is diluted with cold water as required and sprayed or roller coated onto the crust. Can be used in combination with Viepur Cat HP or with Vie Catbase in any proportion, may be colored with non ionic Vietint Pigments for maximum coverage. Hot Ironing or Plating helps to seal off damaged and rough grain giving a dramatic upgrading of Leathers without hardening.

    Example Applications:

    All types of Soft Leathers for Ground coat:

    Water 300 – 500 parts
    Vie Cat Wax 50 – 100 parts
    Viepur Catbase 200 – 300 parts
    Vietint Pigments 0 – 50 parts

    Spray or Roller x 1 wet, dry well and Hot Iron or Plate low pressure some dwell, finish as usual

    High Performance Shoe Leathers, Sofa Leathers etc Ground coat:

    Water 300 – 500 parts
    Viepur Cat HP 50 – 100 parts
    Vie Catbase 200 – 400 parts
    Vie Cat Wax 25 – 50 parts
    Vietint Pigments 0 – 50 parts

    Spray or Roller x 1 wet, dry well and Hot Iron or Plate low pressure some dwell, finish as usual

    Vie CatFill – Encapsulated Microspheres in Cationic Wax/Oil

    Application: Vie CatFill is used as Ground Coat in Finishing to Fill and Seal off damaged grain to upgrade the Leather…It is based on encapsulated polymeric microspheres finely dispersed in a cationic Wax and Oil emulsion.

    The main characteristics are:

    • Good heat and light fastness

    • Seals off rough and damaged grain aiding upgrading as well as for snuffed or corrected leathers for a full grain look with a fine grain break

    • Has extremely high filling and covering power

    • Has an anti-static effect, reducing possible electric shocks during mechanical operations

    Properties:

    • Appearance: creamy white paste

    • Chemical character: fatty acid condensation product

    • Ionic character: cationic

    • Active substance: circa 18% +-1%

    • pH value: approx. 4 – 5

    • Compatibility: good with cationic, amphoteric and nonionic products.

    • Storage stability: minimum 1 year under cool and dry conditions when stored in original, sealed packaging.

    Vie CatFill Application: Vie CatFill is diluted with cold water as required and padded, sprayed or roller coated onto the crust. Can be used in combination with Viepur Cat HP, Vie Catbase and Vie Lustre CC in any proportion, may be colored with non ionic Vie Microtint Pigments for maximum coverage. Hot Ironing or Plating helps to seal off damaged and rough grain giving a dramatic upgrading of Leathers without hardening. Best results are achieved by Polishing with a felt, Cloth, Linen paper or even reversed buffing paper.

    Example Applications:

    All types of Soft Leathers for Ground coat:

    Water 300 – 500 parts
    Vie CatFill 50 – 200 parts
    Viepur Catbase 200 – 400 parts
    Vie Microtint Pigments 0 – 25 parts

    Spray or Roller x 1 wet, dry well and then Polish, Hot Iron or Plate low pressure some dwell, finish as usual

    High Performance Shoe Leathers, Sofa Leathers etc Ground coat:

    Water 300 – 500 parts
    Viepur Cat HP 25 – 50 parts
    Vie CatFill 200 – 400 parts
    Vie Cat Wax 25 – 50 parts
    Vietint Pigments 0 – 25 parts

    Vie Designer Wax

    Solids content: 20%

    PH value: tba

    Composition: Vie Designer Wax is a silica free micronized organic matt polymer homogenized into PE waxes and bound with polishable micro fine aliphatic Polyurethanes and modified with, flow agents etc. Vie Designer Wax has no limit in its ability to help the finisher make a wide range of “Fantasy” Fashion effects only limited by their imagination. Vie Designer Wax has special micronized polymers with a wide range of molecular sizes which give remarkable upgradation at the same time providing the leather with a lush silky soft handle and a natural grain break, keeping Leather as natural as possible. It may be used alone directly onto the crust, or used with Viesol LD dyes on crust or base coated leathers for various two tone antique or marble effects, or add 1-2% Vie Microtint White pigment and make your own White Wax for pigmented pull up or waxed effects.

    The main characteristics are:

    • Covers and fills defects, gives whitish look with high polishability

    • Gives a pleasant Waxy silky feel to the Finish

    • Has good heat and light fastness

    • Can be used as a White wax for fantasy pigmented leathers or with other oils and waxes for a wide range of polishable, burnishable aniline leathers

    • Add to Top coats for Matt, Silk like feeling Leathers, use as complete base to top for Velour and Nubuck type leathers

    Vie Designer Wax Application: Used on all types of Leathers for a wide range of Fashionable Fantasy finishes. Vie Designer Wax is preferably used for high gloss polishing effects on smooth leathers and embossed leathers; it leads to a glossy two tone effect on the tips of the grain. When rotoplating at 110 –120° C the gloss of the leather is increased considerably. By adding Vie Designer Wax to Oils like Vie Oil PW and Waxes like Vie Antik Wax 40 a wide range of controlled white break effects and aged second hand looks can be developed. Use directly onto crust with or without Viesol LD dyes or Vie Microtint pigments for Velour/Nubuck looking and feeling leathers, apply in circular motions by pad, brush or sponge for Marble designs etc

    Example Applications:

    • Add 50 – 150 parts per kg with Vie Oil PW and Vie Antik Wax 40 for increased whitening effect

    • Use as an over-spray Feel coat 100 – 250 parts Vie Designer Wax with 200 – 750 parts Water for a waxy sensuous feel, spray light or as required, can be followed by a light Iron or Hot Plate 100oC + Dry Mill for whitish look

    • Use over pigmented base coats for Fashionable White break look, best results with x 1 – 2 sprays 200 parts Viepur-35 50 parts Vie Microtint pigments and 750 parts water followed by two sprays Vie Designer Wax 500 parts Vie Microtint White pigment 5 – 10 parts Water 475 parts 15-25 parts Viesol LD dyes, and Top coat Vielac W-88 200 parts Water 100 parts Vie Feel SS 2-10 parts. Plate Stake Mill etc to required effect

    Vie Filler SFT(LC)

    Solids content: tba

    PH value: tba

    Composition: Vie Filler SFT(LC) is a soft aqueous fine particle Silica Based Filler/Duller

    The main characteristics are:

    • retains a fine grain and break

    • maintains the softness of the leather, has a pleasant silky, not dry feel

    • Reduces Tack and Gloss of Base coats

    • Has good Heat and Light fastness

    Vie Filler SFT(LC) Application: Use on all types of Leather in the base coat to reduce tack and gloss, and improve plateability and stackability

    Example Applications: Add 50 – 100 parts per kg of base coat mix as required for all types of Leathers

    Vie Filler UG

    Solids content: 47%

    PH value: 6 – 7.5

    Composition: Vie Filler UG is a highly concentrated non-ionic soft aqueous fine particle Silica free upgrading Filler.

    The main characteristics are:

    • Can be used in both Cationic or Anionic Base coats

    • Retains a fine grain and break

    • Maintains the softness of the leather, has a pleasant silky, not dry feel

    • Reduces Tack and Gloss of Base coats

    • Has good Heat and Light fastness

    Vie Filler UG Application: Use on all types of Leather in the base coat to increase coverage and filling properties while also effectively reducing tack and gloss, improves plateability and stackability, and can also be used in Fashion effects like distressed or second hand look, or even mixed with water miscible oils and waxes for whitening effects.

    Example Applications:

    • Add 25 –100 parts per kg in Anionic base coats mix as required for all types of Leathers

    • Add 5 – 25 parts per kg in Cationic base coats mix as required for all types of Leathers

    • Add 5 – 100 parts per kg in Water Miscible Oils and Waxes for various fashion effects

    Vie Foam AX

    Solids content: tba

    PH value: tba

    Composition: Vie Foam AX is an aqueous, anionic derivative of a fatty acid for use in the Vie Foaming system.

    Description: Vie Foam AX is a white liquid of medium to high viscosity. The product is used for foaming Vie Foam mixtures in an appropriate foam generating machine and for the stabilization of this mechanical foam.
    The storage temperature should not be lower than + 10°C and not exceed + 30°C. The drums have to be closed immediately after use.

    • Creates Foam with virtually all Aqueous Base coats

    • Offers a very long lasting and stable Foam matrix

    • Can reduce density from 1 gr/cm to up to 0.5 gr/cm

    Vie Foam AX Application: Vie Foam AX is a Chemical Foam generator. Vie Foam AX is sometimes used together with Vie Foam ST. If used in too high amounts foam density will increase making application difficult. Therefore, the appropriate quantity has to be ascertained by pre-trials. The quantity applied varies between 8 and 30 g/kg mix to be foamed. The product should be added shortly before foaming.

    Example Applications:

    • 25–50 p. Vie Foam AX and 5–15 p. Vie Foam ST related to 1 kg unfoamed Vie Foam base coat mix has been found to give optimum results

    • Spray x 1 -2 base coat: Water 200 parts Vie Super Penetrator LC 25 parts Viecryl 7 100 parts Viecryl 61 300 parts Vie Lustre SS 50 parts Vie Lustre H 50 parts Vie Wax 60 100 parts Vie Microtint Black/Jet Black 75 parts Viesol LD Black W 25 parts.

    • Attention: Stir product thoroughly shortly before use! Add it to the rest of the mix together with Vie Foam ST, shortly before foaming.

    Vie Foam ST

    Solids content: tba

    PH value: tba

    Composition: Vie Foam ST is an APEO/NPE free stabilizer and wetting agent for use in the Vie Foaming system.

    Description: Vie Foam ST is a slightly yellowish-white liquid of medium to high viscosity. The product is used as an auxiliary agent for Vie Foam finishing. Vie Foam ST is used to give the following properties:

    • improvement of both wettability and rewettability

    • stabilisation of the foam

    • avoids cracking of foam coat during drying process

    • Improves both wettability and re-wettability

    • Stabilization of the mechanical foam, maintains even foam size

    • Helps Flow out of Base coats

    • Avoids cracking of the Foam coat during drying process

    Vie Foam ST Application: Vie Foam ST can be added to the preparations which will be foamed in quantities of 0.5–2 % relative to the mix. Vie Foam ST is only used together with Vie Foam AX. If used in too high amounts a negative impact on the wet rub values might be the result. Therefore, the appropriate quantity has to be ascertained by pre-trials.

    Example Applications:

    • 25–50 p. Vie Foam AX and 5–15 p. Vie Foam ST related to 1 kg unfoamed Vie Foam base coat mix has been found to give optimum results

    • Attention: Stir product thoroughly shortly before use! Add it to the rest of the mix together with Vie Foam AX, shortly before foaming.

    Vie Ground GB

    Solids content: 27%

    PH value: tba

    Composition: Vie Ground GB is a Weakly Cationic Polymer containing, Wax/Oil Ground

    Description: Vie Ground GB is a white, low viscous liquid. The product is polishable, reduces the absorbency of the leather and gives a good filling and a smooth handle. Vie Ground GB can be used universally in anionic and cationic mixes. The product is an excellent anti-sticker without affecting negatively the intermediate adhesion. The finish will not be hardened. When used in pregrounds, leather defects are not highlighted.

    The main characteristics are:

    • Reduces Tack and Improves Plate release in Base and Top coats

    • Gives a pleasant Waxy silky feel to the Finish

    • Has average heat and light fastness

    • Seals off Damaged Grain, maintains Leather Softness

    Vie Ground GB Application: Vie Ground GB is universally used as filling agent and anti-sticker in base coats, pre-grounds and polish grounds. It seals off damaged grain, gives a high level of upgrading without overloading the finish.

    • Anionic Add 25 – 100 parts per kg in aqueous Base Coats for all types of Leathers to improve plate release, increase softness and seal off damaged grain

    • Cationic Add 25 – 75 parts per kg in aqueous Base coats for all types of Leathers to increase softness, plate release and seal off damaged grain

    Vie Lustre CC

    Solids content: 10%

    PH value: 3 – 5

    Composition: Vie Lustre CC is a Cationic Medium Hard natural Protein based on Casein for Garment, Shoe and Fancy goods Leathers.

    The main characteristics are:

    • Reduces Tack and Increases Gloss in Cationic Base coats

    • Gives a Silky Soft Protein feel to the Finish

    • Improves Stacking and Embossing properties without hardening the finish

    • Can be used in Cationic Finishes to increase heat resistance

    Vie Lustre CC Application: Used on many types of Leathers in Base coats to give a Glossy Natural Protein look and feel.

    Example Applications:

    Cationic Sealer/ Base Coat for Softee type Leathers

    Water 300 – 500 parts
    Viepur Cat HP 25 – 50 parts
    Viepur Cat Base 200 – 400 parts
    Vietint Pigments 25 – 50 parts
    Vie Lustre CC 25 – 100 parts

    Spray, Pad or Roller coat x 1 wet

    Finish as usual with anionic base and/or top coats

    Vie Lustre H

    Solids content: tba

    PH value: tba

    Composition: Vie Lustre H is a Hard Casein based natural Protein for Shoe and Fancy goods Leathers.

    The main characteristics are:

    • Reduces Tack and Increases Gloss in Base and Top coats

    • Gives a Natural Protein feel to the Finish

    • Has much improved Stacking and Embossing properties compared to many synthetic Proteins

    • Can be used in polish coats or for Traditional Glazed Leathers

    Vie Lustre H Application: Used mainly on Shoe Upper and Fancy Goods Leathers in Base or Top coats to give a Glossy Natural Protein look and Feel.

    Example Applications:

    • Add 50 – 100 parts per kg in aqueous Top Coats for Fancy Goods Leathers

    • Use 100 – 200 parts per kg in base coats for Imitation Glazed Look, Iron or Hot Plate 100oC +

    • Use with other softer Proteins for Traditional Glazed Finishes

    Vie Lustre SS

    Solids content: tba

    PH value: tba

    Composition: Vie Lustre SS is a silky soft modified natural Protein based on Casein for Garment, Shoe and Fancy goods Leathers.

    The main characteristics are:

    • Reduces Tack and Increases Gloss in Base and Top coats

    • Gives a Silky Soft Protein feel to the Finish

    • Improves Stacking and Embossing properties without hardening the finish

    • Can be used in polish coats or for Traditional Glazed Leathers

    Vie Lustre SS Application: Used on many types of Leathers in Base coats to give a Glossy Natural Protein look and feel.

    • Use 50 – 150 parts per kg in base coats for Imitation Glazed Look, Iron or Hot Plate 100oC +

    • Use with other harder Proteins for Traditional Glazed Finishes

    VIE LUSTRE XK

    Solids content: tba

    PH value: 8-10

    Composition:Vie Lustre XK is a Very Hard Casein based natural Protein for Shoe and Fancy goods Leathers

    The main characteristics are:

    • Reduces Tack And Increases Gloss In Base And Top Coats

    • Gives A Natural Protein Feel To The Finish

    • Has Much Improved Stacking And Embossing Properties Compared To Many Synthetic Proteins

    • Can Be Used In Polish Coats Or For Traditional Glazed Leathers

    • Used For Fashionable Cracking Effects With Viecryl Crack Etc

    Vie Lustre XK Application: Used on many types of Leathers in Base coats to give a Glossy Natural Protein look and feel.

    • Add 50 – 100 parts per kg in aqueous Top Coats for Fancy Goods Leathers

    • Use 100 – 200 parts per kg in base coats for Imitation Glazed Look, Iron or Hot Plate 100oC +

    • Use with other softer Proteins for Traditional Glazed Finishes

    • Use with Viecryl Crack for Fashionable Cracking or Second Hand Mill off effects

    VIE PE WAX 35

    Solids content: 20%

    PH value: 8-10

    Composition:Vie PE Wax 35 is a non ionic emulsion based on polyethylene wax for improving the surface properties of all types of aqueous coatings and polishes

    The main characteristics are:

    • Reduces Tack, Increases Anti-Slip Effect And Improves Abrasion Resistance

    • Gives A Pleasant Waxy Silky Feel To The Coating

    • Has Good Heat And Light Fastness

    • Increases Buffability, Increases Filling Capacity

    VIE PE WAX 35 Application:

    Vie PE Wax 35 improves the buffability, increases filling capacity and produces an anti-slip effect. The above mentioned properties are generated by mixing Vie PE Wax 35 with polymers in a ratio of 3:1 (solid wax to solid polymer). A mixing ratio of 1:6 increases the water- and alcohol-resistance, the protection against heel marks (= foot traffic resistance), and the dirt-repellent action. Vie PE Wax 35 is compatible with all known polymer dispersions and plasticizers.

    VIE REVIVE CT

    Solids content: tba

    PH value: tba

    Composition:Vie Revive CT is a high viscosity cationic polyurethane dispersion containing high filling encapsulated microspheres and other high filling substances. Vie Revive CT is designed to be thixotropic and with mechanical action like stirring, spraying, roller coating or padding viscosity drops and allows the technician to apply a high covering and filling layer especially deep into the natural defects like pinholes etc and after thorough drying can be easily polished on a cloth, felt, linen or reversed buffing paper to remove surface material, followed by a light finish to level off colour and complete upgrading. Viesol LD dyes or Vie Microtint pigments may be added to match colour as close as possible to completely cover minor defects and improve cutting value without changing the softness and drape of the leather

    The main characteristics are:

    • Retains A Finer Grain And Break Than Other Stuccos

    • Dramatically Upgrades And Can Even Fill Open Scratches And Pinholes Etc

    • Gives High Coverage, And Excellent Buffing Or Polishing Properties

    • Has Excellent Light And Heat Resistant

    Description PENETRATOR LC:

    Vie Revive CT is a product with a white paste like appearance. Vie Revive CT is used as a Stucco like filler to cover deep defects, like brand-marks, thorn scratches etc on the leather surface so that they become invisible after finishing. Due to its composition, the product can be buffed or polished well without smearing. Vie Revive CT can also be added to Cationic base coats to increase volume and therefore coverage and filling, especially suited for Roller coat or hand padding application as the microspheric polymers may effect rheology and spraying levelness. Adjusting viscosity will reduce the splatter effect.

    VIE REVIVE CT Application:

    Vie Revive CT can be applied without dilution on the leather surface by hand with a spatula. Care must be taken that all defects which should be covered on the surface must be completely filled up with the product, a second coat may be applied to be sure. After drying, the leathers can be buffed or polished to remove any surplus of Vie Revive CT. Vie Revive CT can be coloured with Vie Microtint pigments or Viesol LD dyes up to 5 %, compatibility needs to be checked and water may be used to improve this. Another main area of success for Vie Revive CT is on nappa and garment leathers especially Ovine, pad and/or spray unfinished crust with Vie Revive CT diluted 2: 1 to 1: 1 with water and colored with 2% Viesol LD dye (diluted in 3% water) and 5% Vie Microtint pigment, addition of 5% Viepur Cat HP will improve flex and adhesion but polishability needs checking, dry well and polish clean on a felt, linen, cloth, or reversed buffing paper and finish as required, often a colour adjustment and a lacquer and feel top…

    VIE REVIVE ESCAPE

    Solids content: tba

    PH value: tba

    Composition:Vie Revive Escape is a thixotropic aqueous aliphatic polyurethane dispersion containing high filling encapsulated microspheres and other synergistic substances.

    The main characteristics are:

    • Retains A Finer Grain And Break Than Other Stuccos

    • Dramatically Upgrades And Can Even Fill Open Scratches And Ticks

    • Gives High Coverage, And Excellent Buffing Properties

    • Has Excellent Light And Heat Resistant

    Description PENETRATOR LC:

    Vie Revive Escape is a product with a white paste like appearance. Vie Revive Escape is used as a Stucco like filler to cover deep defects, like brand-marks, thorn scratches etc on the leather surface so that they become invisible after finishing. Due to its composition, the product can be buffed well without smearing. Vie Revive Escape can also be added to base coats to increase volume and therefore coverage and filling, especially suited for Roller coat application as the microspheric polymers may effect rheology and spraying levelness. Vie Revive Escape shows excellent adhesion on virtually any substrate, cloth, metals, cork, microfiber etc. When used on splits if applied by reversed roller coater or by Spatula it can fill the fibres and allows the technician to produce full grain or snuffed grain looking leathers. Can be used on Hemp, Cotton, Sack cloth etc to fill coarse fibres and give a suede like feel and look, it may be colred with Viesol LD dyes or Vie Microtint pigments and applied by Screen print or design roller or by any method for a multitude of fashion effects

    VIE REVIVE ESCAPE PENETRATOR LC Application:

    Vie Revive Escape is applied without dilution on the leather surface by hand with a spatula, sponge or roller.

    Care must be taken that all defects which should be covered on the surface must be completely filled up with the product, a second coat may be applied to be sure. After drying, the leathers will be buffed to remove any surplus of Vie Revive Escape. Vie Revive can be coloured with Viesol LD dyes up to 5% and/ or Vie Microtint pigments up to 10%. Buffing is not technically necessary and for fashion effects is often not used. A variety of coats with different colours may be applied on top of each other.

    VIE REVIVE FG

    Solids content: tba

    PH value: tba

    Composition:Vie Revive FG is a high viscosity anionic polyurethane dispersion containing high filling encapsulated microspheres and other high filling substances. Vie Revive FG is designed to be thixotropic and with mechanical action like stirring, spraying, roller coating or padding viscosity drops and allows the technician to apply a high covering and filling layer especially deep into the natural defects like pinholes etc and after thorough drying can be easily polished on a cloth, felt, linen or reversed buffing paper to remove surface material, followed by a light finish to level off colour and complete upgrading. Viesol LD dyes or Vie Microtint pigments may be added to match colour as close as possible to completely cover minor defects and improve cutting value without changing the softness and drape of the leather

    The main characteristics are:

    • Retains A Finer Grain And Break Than Other Stuccos

    • Dramatically Upgrades And Can Even Fill Open Scratches And Pinholes Etc

    • Gives High Coverage, And Excellent Buffing Or Polishing Properties

    • Has Excellent Light And Heat Resistant

    Description PENETRATOR LC:

    Vie Revive FG is a product with a white paste like appearance. Vie Revive FG is used as a Stucco like filler to cover deep defects, like brand-marks, thorn scratches etc on the leather surface so that they become invisible after finishing. Due to its composition, the product can be buffed or polished well without smearing. Vie Revive FG can also be added to base coats to increase volume and therefore coverage and filling, especially suited for Roller coat or hand padding application as the microspheric polymers may effect rheology and spraying levelness. Adjusting viscosity will reduce the splatter effect.

    VIE REVIVE FG PENETRATOR LC Application:

    Vie Revive FG is applied without dilution on the leather surface by hand with a spatula. Care must be taken that all defects which should be covered on the surface must be completely filled up with the product, a second coat may be applied to be sure. Vie Revive FG may also be diluted 2:1 with water and sprayed. Adding a little Viesol LD dye or Vie Microtint pigments may help coverage and levelling. After drying, the leathers will be polished to remove any surplus of Vie Revive.

    Vie Revive FG can be coloured with Vie Microtint pigments or Viesol LD dyes up to 5 %, compatibility needs to be checked and water may be used to improve this. Another main area of success for Vie Revive FG is on nappa and garment leathers especially ovine, pad and/or spray unfinished crust with Vie Revive FG diluted 2: 1 to 1: 1 with water and colored with 2% Viesol LD dye (diluted in 3% water) and 5% Vie Microtint pigment, addition of 5% Viepur-35 will improve flex and adhesion but polishability needs checking, dry well and polish clean on a felt, linen, cloth, or reversed buffing paper and finish as required, often a colour adjustment and a lacquer and feel top…

    VIE REVIVE

    Solids content: tba

    PH value: tba

    Composition:Vie Revive is a high viscosity polyurethane dispersion containing high filling encapsulated microspheres and other high filling substances.

    The main characteristics are:

    • Retains A Finer Grain And Break Than Other Stuccos

    • Dramatically Upgrades And Can Even Fill Open Scratches And Ticks

    • Gives High Coverage, And Excellent Buffing Propertie

    • Has Excellent Light And Heat Resistant

    Description PENETRATOR LC:

    Vie Revive is a product with a white paste like appearance. Vie Revive is used as a Stucco like filler to cover deep defects, like brand-marks, thorn scratches etc on the leather surface so that they become invisible after finishing. Due to its composition, the product can be buffed well without smearing. Vie Revive can also be added to base coats to increase volume and therefore coverage and filling, especially suited for Roller coat application as the microspheric polymers may effect rheology and spraying levelness.

    VIE REVIVE PENETRATOR LC Application:

    Vie Revive is applied without dilution on the leather surface by hand with a spatula. Care must be taken that all defects which should be covered on the surface must be completely filled up with the product, a second coat may be applied to be sure.

    After drying, the leathers will be buffed to remove any surplus of Vie Revive. Vie Revive can be coloured with Viepaque pigments or Vietint Ultrafine pigments up to 10%.

    VIE SUPER PENETRATOR LC

    Solids content: tba

    PH value: tba

    Composition:Vie Super Penetrator LC is an APEO/NPE free penetrator for all types of Leathers

    The main characteristics are:

    • Highly Effective To Aid Penetration On All Types Of Leathers

    • Used For Impregnation Or Base Coats

    • Helps Flow Out Of Base Coats

    • High Strength And Is Effective Even At Low Dosage Levels

    VIE SUPER PENETRATOR LC Application:

    Use on all types of Leather in the Impregnation, Adhesion, Sealer or Base coat to improve penetration

    Example Applications:

    1/ Add 25 – 75 parts per kg in aqueous Base Coats for all types of Leathers to improve plate release and softness

    1/ Add 100 – 150 parts per kg in Impregnation coat, adhesion or sealer coats 2/ Add 25 – 100 parts per kg in base coats

    VIE WAX 203

    Solids content: 11%

    PH value: tba

    Composition:Vie Wax 203 is an aqueous Synthetic Wax emulsion for all types of Leathers

    The main characteristics are:

    • Reduces Tack And Improves Plate Release In Base And Top Coats

    • Gives A Pleasant Waxy Silky Feel To The Finish

    • Has Good Heat And Light Fastness

    • Can Be Used Also As An Over-Spray On Finished Leathers To Improve Feel

    VIE WAX 203 Application:

    Used on all types of Leathers mainly in the Base coat to give a waxy feel and improve plate release

    Example Applications:

    1/ Add 25 – 75 parts per kg in aqueous Base Coats for all types of Leathers to improve plate release and softness

    2/ Use as an over-spray Feel coat 100 – 250 parts Vie Wax 203 with 400 – 750 parts Water for a waxy feel or can also add 2 – 5 parts Vie Feel AR or Vie Feel SW for a more silky sensuous feel, spray light or as required, can be followed by a light Iron or Hot Plate 80oC +

    VIE WAX 250

    Solids content: 7%

    PH value: tba

    Composition:Vie Wax 250 is an aqueous Synthetic Wax emulsion for all types of Leathers

    The main characteristics are:

    • Reduces Tack And Improves Plate Release In Base And Top Coats

    • Gives A Pleasant Waxy Silky Feel To The Finish

    • Has Good Heat And Light Fastness

    • Can Be Used Also As An Over-Spray On Finished Leathers To Improve Feel

    VIE WAX 250 Application:

    Used on all types of Leathers mainly in the Base coat to give a waxy feel and improve plate release

    Example Applications:

    1/ Add 35 – 100 parts per kg in aqueous Base Coats for all types of Leathers to improve plate release and softness

    2/ Use as an over-spray Feel coat 100 – 250 parts Vie Wax 250 with 200 – 750 parts Water for a waxy feel or can also add 2 – 5 parts Vie Feel S4 or Vie Feel SW for a more silky sensuous feel, spray light or as required, can be followed by a light Iron or Hot Plate 80oC +

    VIE WAX 812

    Solids content: tba

    PH value: tba

    Composition:Vie Wax 812 is a synergistic blend of synthetic and Carnauba Waxes in emulsion form for all types of Fashion Leathers

    The main characteristics are:

    • Use Alone, Or With Penetrator Etc For Burnish Leathers

    • Gives A Pleasant Waxy Natural Feel To The Finish

    • Has Good Darkening In The Shoe Room With Carnauba Wax Bars And Wool Mop

    • Can Be Used Also With Protein Binders For Various Fashion Effects

    VIE WAX 812 Application:

    Used on all types of Fashion Leathers mainly alone or with penetrators as first spray coat or in the Base coat to give a Waxy Feel and improve darkening in the shoe room

    Example Applications:

    1/ Use alone or with Water and Vie Super penetrator as first coat for Semi Veg Burnish Leathers

    2/ Use with Vie Lustre H and Vie Lustre SS for Glossy Burnish Leathers, can be followed by a light Iron or Hot Plate 90 – 110oC

    VIE WAX 816

    Solids content: 20%

    PH value: tba

    Composition: Vie Wax 816 is a special blend of aqueous Synthetic Wax emulsions with polymers added for physicals and feel for all types of Leathers but particularly Fancy Goods

    The main characteristics are:

    • Reduces Tack And Improves Plate Release In Base And Top Coats

    • Gives A Pleasant Waxy Silky Feel To The Finish

    • Has Good Heat And Light Fastness

    • Can Be Used Also As An Over-Spray On Finished Leathers To Improve Feel And Gloss

    VIE WAX 816 Application:

    Used on all types of Leathers mainly in the Base coat to give a waxy feel increase gloss and improve plate release. Vie Wax 816 is preferably used for high gloss polishing effects on smooth leathers and embossed leathers; it leads to a glossy effect on the tips of the grain. When rotoplating at 110 –120° C the gloss of the leather is increased considerably. By adding Vie Wax 816 to glossy Water lacquers (10 – 20%) the wet rubs and the water drop resistance will normally be increased. This property improvement occurs approx. one week (depending on the temperature) after application.

    Example Applications:

    1/ Add 35 – 100 parts per kg in aqueous Base Coats for all types of Leathers to improve plate release and gloss

    2/ Use as an over-spray Feel coat 100 – 250 parts Vie Wax 816 with 200 – 750 parts Water for a waxy feel or can also add 2 – 5 parts Vie Feel S4 or Vie Feel SW for a more silky sensuous feel, spray light or as required, can be followed by a light Iron or Hot Plate 100oC +

    VIE WAX FA-01 FASHION WAX

    Solids content: 20%

    PH value: tba

    Composition: Vie Wax FA-01 is a special blend of aqueous Synthetic Wax emulsions with PE waxes, silicones and Aliphatic Polyurethane polymers designed to help the finisher make a wide range of “Fantasy” Fashion effects only limited by your imagination. Unlike most White waxes Vie Wax FA-01 gives leather a silky soft handle with a natural grain break, keeping Leather as natural as possible

    The main characteristics are:

    • Covers Defects, Gives Whitish Look With High Polishability

    • Gives A Pleasant Waxy Silky Feel To The Finish

    • Has Good Heat And Light Fastness

    • Can Be Used As A White Wax For Fantasy Pigmented Leathers Or With Other Oils And Waxes For A Wide Range Of

    • Polishable, Burnishable Aniline Leathers

    VIEMATT 78 Application:

    Used on all types of Leathers for a wide range of Fashionable Fantasy finishes. Vie Wax FA-01 is preferably used for high gloss polishing effects on smooth leathers and embossed leathers; it leads to a glossy two tone effect on the tips of the grain. When rotoplating at 110 –120° C the gloss of the leather is increased considerably. By adding Vie Wax FA-01 to Oils like Vie Oil PW and Waxes like Vie Antik Wax 40 a wide range of controlled white break effects and aged second hand looks can be developed

    Example Applications:

    1/ Add 50 – 150 parts per kg with Vie Oil PW and Vie Antik Wax 40 for increased whitening effect

    2/ Use as an over-spray Feel coat 100 – 250 parts Vie Wax FA-01 with 200 – 750 parts Water for a waxy sensuous feel, spray light or as required, can be followed by a light Iron or Hot Plate 100oC + Dry Mill for whitish look

    3/ Use over pigmented base coats for Fashionable White break look, best results with x 1 – 2 sprays 200 parts Viepur-35 50 parts Vie Microtint pigments and 750 parts water followed by two sprays Vie Wax FA-01 500 parts Water 475 parts 25 parts Viesol LD dyes, and Top coat Vielac W-88 200 parts Water 100 parts Vie Feel SS 2-10 parts. Plate Stake Mill etc to required effect

    VIEMATT 78

    Solids content: 19%

    PH value: 8+-

    Composition: Viematt 78 is a soft aqueous fine particle Silica Based Filler/Duller.

    The main characteristics are:

    • Retains A Fine Grain And Break

    • Has A High Matting Effect With Excellent Light And Heat Fastness

    • Improves Feel And Surface Levelness And Coverage

    • Reduces Tackiness, Improves Plating And Stacking Properties

    VIEMATT 78 Application:

    Use on all types of Leather in the base coat to reduce tack and gloss, and improve plateability and stackability. Due to its characteristics it is especially suitable for matting high-quality base coats, e. g. car upholstery. In general Viematt 78 is also a suitable component in conventional upholstery and shoe upper leather base coats. Viematt 78 may also be used to Dull Aqueous Top coats for general purpose Leathers

    Example Applications:

    Add 25 – 100 parts per kg of base coat mix as required for all types of Leathers. Due to its Thixotropic nature stir well before use.

    Live test the caliber of our products

    Request for free product demo

    Let us contact you to understand your requirements and deliver sample the product of your choice.